Kenwood KNA-DV2600 Instruction Manual Download Page 67 | Manualshive

Page: 67 / 72

background image

English

|

67

■

Setting the AV IN-2 Mode <VD2>

Touch

Setting

[

7

AV-IN1]

It becomes the video mode setting. Operate the
V.SEL button when the image from the device
connected to <AV IN-2> terminal is shown on the
monitor.

[

7

OFF]

It becomes the OFF mode setting.Use this setting
when there’s nothing connected to the <AV IN-2>
terminal.

■

Setting the Camera Mode <CAMERA/VIDEO>

Touch

Setting

[

7

AUTO]

It becomes the Rear view camera mode setting.
When the reverse sensor cable is powered up, the
monitor image is switched to the image of the
device connected to the <CAMERA VIDEO IN>
terminal.

[

7

VD]

It becomes the video mode setting. Operate the
V.SEL button when the image from the device
connected to <CAMERA VIDEO IN> terminal is
shown on the monitor.

[

7

OFF]

It becomes the off mode setting.Use this setting
when there’s nothing connected to the <CAMERA
VIDEO IN> terminal.

■

Switching to the System Setup screen -2

Touch the [

3

] button.

■

Exit the System Setup screen

Touch the [RTN] button.

Return to the Setup Menu screen.

System Setup screen-2

■

Setting the AV Output Mode <AV OUT>

Touch

Setting

[

7

NORMAL]

Picture/sound with monitor picture

[

7

NAV]

Navigation Sound

[

7

VD1]

Picture/sound from <AV IN-1> terminal

[

7

VD2]

Picture/sound from <AV IN-2> terminal

■

Touch Sensor Tone <BEEP>

Setting the operation check sound (beep sound)
ON/OFF.

Touch

Setting

[

7

ON]

Touch sensor tone is turned on

[

7

OFF]

Touch sensor tone is turned off

■

Return to the System Setup screen -1

Selet the [

2

] button.

■

Exit the System Setup screen

Touch the [RTN] button.

Return to the Setup Menu screen.

KNA-2600̲r3.0̲English.Indd 67

03.12.4, 10:32:12 PM

«
...
65
66
67
68
69
...
»

Summary of Contents for KNA-DV2600









































































Reviews:

No comments

Related manuals for KNA-DV2600

Brand: Rain Bird Pages: 96

Brand: Clarion Pages: 85

Brand: Power Acoustik Pages: 46

Brand: Ebinger Pages: 48

Brand: Cadillac Pages: 154

Brand: Blaupunkt Pages: 27

Brand: Discount Car Stereo Pages: 9

Brand: flexvision Pages: 13

NavMate NM-PN600

Brand: Horizon Navigation Pages: 38

Brand: TOOLCRAFT Pages: 12

Brand: HANDYMAP Pages: 12

Brand: Sune Technology Pages: 24

Brand: Pioneer Pages: 32

Brand: Pioneer Pages: 57

Brand: Pioneer Pages: 74

Brand: Pioneer Pages: 120

AVICF500BT - CD-VM1 Optional Microphone

Brand: Pioneer Pages: 129

Brand: Pioneer Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands