Kenwood KNA-DV2600 Instruction Manual Download Page 64

Page: 64 / 72

English

AVN-2675's Monitor Unit

Basic Operations

Turning ON/OFF the power

Power Turning on the power:

Press the [V.SEL] button.

Turning off the power (Stand by mode):

Press the [V.SEL] button for at least 1 second.

Switching the Picture

Press the [V.SEL] button.

Each time the button is pressed the monitor’s picture
switches as follows:

Display

Picture

"NAV"

Navigation (During "NAV" set to "RGB" or "AV IN1")

"VD1"

Video 1 (During "VD1" set to "AV-IN1")

"VD2"

Video 2 (During "VD2" set to "AV-IN2")

"CAM"

Video 3 (During "CAMERA/VIDEO" set to "VD")

• For "NAV", "VD" and "CAMERA/VIDEO" setting, refer to

<System Setup screen> (see page 66).

• You cannot view video pictures whilst the vehicle is

moving. To enjoy video pictures, find a safe place to
park and engage the parking brake.

Adjusting the Volume

Increasing Volume:

Press the [up] button.

Decreasing Volume:

Press the [down] button.

Switching the Video Screen Mode

Press the [WIDE MODE] button.

Each time the button is pressed the screen mode
switches as follows:

Display

Setting

Screen Mode

"FULL"

Full screen
mode

"ZOOM"

Zoom screen
mode

"JUST"

Just screen
mode

"NORMAL"

Normal screen
mode

N O R M A

F U L L

N O R M A

S P

W D

A V

V D 1

V S

WIDE MODE

V.SEL

down

KNA-2600̲r3.0̲English.Indd 64

03.12.4, 10:31:57 PM

Summary of Contents for KNA-DV2600









































































Search results

Summary of Contents for KNA-DV2600

Reviews:

Related manuals for KNA-DV2600

Brands by name

Popular brands

Kenwood KNA-DV2600, Instruction Manual

Search results

Summary of Contents for KNA-DV2600

Reviews:

Related manuals for KNA-DV2600

Brands by name

Popular brands