ENGLISH
65
CONNECTION/INSTALLATION
CONNECTION/INSTALLATION
Before installing the unit
V
WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red)
and the battery wire (yellow). The power supply
must be connected to the wires via the fuse.
V
Precautions on installation and connection
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12 V
DC power supply.
• Do not install the unit in a location exposed to
direct sunlight or excessive heat or humidity. Also
avoid places with too much dust or the possibility
of water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned on (“Miswiring DC Offset
Error”, “Warning DC Offset Error” is displayed),
the speaker wire may have a short circuit or
have touched the chassis of the vehicle and the
protection function may have been activated.
Therefore, the speaker wire should be checked.
• Keep all cables away from heat dissipating metal
parts.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to a
power source with a constant voltage supply, such
as with battery wires, the battery may be drained.
• Only for DDX7017BT/DDX7017BTM/DDX717WBT/
DDX717WBTM:
If the console has a lid, make sure to install the
unit so that the monitor panel will not hit the lid
when closing and opening.
• If the fuse blows, first make sure the wires are not
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the
·
wires or ground them to any metal part in the car.
• When only two speakers are being connected to
the system, connect both connectors either to
the front output terminals or to the rear output
terminals (do not mix front and rear). For example,
if you connect the
ª
connector of the left speaker
to a front output terminal, do not connect the
·
connector to a rear output terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30°
or less.
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise
scratches, damage, or failure may result.
V
CAUTION
• Install this unit in the console of your vehicle.
Do not touch the metal parts of this unit during
and shortly after the use of the unit. Metal parts
such as the heat sink and enclosure become hot.
• When parking at a low ceiling area:
– For DDX7017BT/DDX7017BTM/DDX4017BT/
DDX417BT/DDX417BTM: Turn off the unit to
store the antenna.
As when the unit is installed in the car with the
function of auto antenna; the radio antenna
extends automatically when you turn on the
unit with the antenna control wire (ANT CONT)
connected. (Pages 67 and 68).
– For DDX717WBT/DDX717WBTM: Turn off the
unit to store the antenna or change to any
other source than Radio with
[OFF]
is selected
for
<Antenna Control>
on
<Radio Mode>
screen. (Page 32)
2017DDX-Entry̲M.indb 65
2017DDX-Entry̲M.indb 65
2016/12/22 14:56
2016/12/22 14:56
