Kenmore 415.16505900 Use And Care Manual Download Page 9

CAUTION

SPIDER ALERT!

GAS COLLECTOR

BOX & IGNITOR

VALVE

CONTROL PANEL

BURNER

VENTURI

LIFT OUT

BURNER ASSEMBLY

AIR

SHUTTER

SPIDER WEBS

INSIDE VENTURI

SPIDER WEBS

INSIDE VENTURI

CLEAN OUT 

VENTURI

REMOVE 

BURNER

CLIPS

If you notice that your grill is getting hard to light or that the 
flame isn’t as strong as it should be, take the time to check and 
clean the venturi’s.

In some areas of the country, spiders or small insects have been 
known to create “flashback” problems. The spiders spin webs, build 
nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of 
gas to the burner. The backed-up gas can ignite in the venturi behind 
the control panel. This is known as a flashback and it can damage 
your grill and even cause injury.

To prevent flashbacks and ensure good performance the burner and 
venturi assembly should be removed from the grill and cleaned 
before use whenever the grill has been idle for an extended period.

Turning Grill Off

•Turn all knobs to  

OFF 

 position. Turn LP tank off by turning 

OPD hand wheel clockwise to a full stop.

Ignitor Check

•Turn gas off at LP tank.

 Press and hold ignitor button.  "Click" 

should be heard and spark seen each time between collector 
box or burner and electrodes. See 

"Troubleshooting"

 if no click 

or spark.

Valve Check

•Important: Make sure gas is off at LP tank before checking 

valves

.  Knobs lock in  

OFF 

 position. To check valves, first 

push in knobs and release, knobs should spring back. If knobs 
do not spring back, replace valve assembly before using grill. 
Turn knobs to

 LO

 position then turn back to  

OFF 

 position. 

Valves should turn smoothly.  

General Grill Cleaning 

•Keep the outside of your grill looking new by cleaning it once a 

month with warm soap and water or a non-abrasive cleaner. If 
you don’t have a grill cover, wipe off dust and grime before 
starting your grill.

• Coating the cooking grids with spray-on cooking oil will keep the 

food from sticking and make clean up easier. After cooking, 
scrape the grates with a long handled, brass wire bristle brush.

•Check inside the grill bottom for grease build up and clean 

often, especially after cooking fatty meat. 

•Do not mistake brown or black accumulation of grease and 

smoke for paint.  Apply a strong solution of detergent and water 
or use a grill cleaner with scrub brush on insides of grill lid and 
bottom. Rinse and allow to completely air dry. 

Do not apply a 

caustic grill/oven cleaner to painted surfaces.

 

•Plated wire grates:

 Wash grates with concentrated grill 

cleaner or use soap and water solution. Dry thoroughly and 
store indoors between cookouts. 

• 

Plastic parts: 

Wash with warm soapy water and wipe dry.

s

 

Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

•Porcelain grates: 

Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner.

 

Use non-abrasive scouring 

powder for stubborn stains.

•Painted surfaces: 

Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

•Stainless steel surfaces: 

To maintain your grill’s high quality 

appearance, wash with mild detergent and warm soapy water 
and wipe dry with a soft cloth after each use. Baked-on grease 
deposits may require the use of an abrasive plastic cleaning 
pad. Use only in direction of brushed finish to avoid damage. 
Do not use abrasive pad on areas with graphics.

• Cooking surfaces:

 If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on

cooking surfaces prior to grilling. It is not recommended to

clean cooking surfaces while grill is hot.

Storing Your Grill

• Clean cooking grates.

• Store in dry location.  

• When LP tank is connected to grill, store outdoors in well-

ventilated space and out of reach of children. 

• Cover grill if stored outdoors.

• Store grill indoors ONLY if LP tank is turned off and 

disconnected, removed from grill and stored outdoors.

• When removing grill from storage follow 

"Cleaning Burner 

Assembly" 

instructions before starting grill.

464722309 • 464722509 • 9

Summary of Contents for 415.16505900





























Reviews: