Keith LeakProof III Owner'S Manual Download Page 9

OWNER / OPERATOR MANUAL 

LeakProof III

        

 

 

 

 

 

DOC06436  Rev B

2.2  Floor to Wet Kit Diagram

NOTE:

 Refer to Parts Catalog for additional information on fittings.

To have proper operation of your KEITH

®

 

WALKING FLOOR

 Unloader, the following check list and diagram 

must be followed.  This is critical or your warranty may be voided.

TRACTOR:

  1) Male quick coupler to be on the return line 

(Line through filter to tank).

                     2) Female quick coupler to be on pressure line 

 

 

(Line from pump).

TRAILER:

    1) Female quick coupler to be on return line 

 

 

(Line from switching valve port stamped “RES”)

                     2) Male quick coupler to be on pressure line 

 

 

(Line to switching valve port stamped “PUMP”).

If you have any questions of problems, call KEITH Manufacturing Co. (541) 475-3802 or (800) 547-6161

 

 

 

 

 

 

 

     

Return Line

Reservoir

   

 

 

 

Relief Valve

Trailer Return Line 

Female Quick Coupler

Tractor Return Line 

Male Quick Coupler

Filter Heads

Lines to and 

from Drive Unit

Trailer Pressure Line 

Male Quick Coupler

Tractor Pressure Line 

Female Quick Coupler

Pressure Line

NOTE: PRESSURE LINE

MUST BE ATTACHED TO

THIS PORT!!!

Switching Valve

3/4” Pressure 

Relief Hose

2” Suction Hose

Pump 

P.T.O.

Summary of Contents for LeakProof III



















Reviews: