Keith LeakProof III Owner'S Manual Download Page 3

OWNER / OPERATOR MANUAL 

LeakProof III

        

 

 

 

 

 

ii 

DOC06436  Rev B

Introduction

We at KEITH Manufacturing Co. are very happy you have decided to equip your trailer with the KEITH

®

 

WALKING FLOOR

®

 system.  We take great pride in manufacturing the simplest, lowest maintenance self-

unloading system available.  Installing the KEITH

®

 

WALKING FLOOR

®

 system in your trailer provides you 

with the versatility to load or unload virtually any type of material. 

The following pages contain information on the operation of your KEITH

®

 

WALKING FLOOR

®

 system.  

Further support and safety documents (manuals, brochures, and product specs) can be viewed or 

downloaded from our website at www.KeithWalkingFloor.com.

In addition, we have provided general information on the type of hydraulic wet kit that will be needed to 

operate your system.  Please contact a KEITH sales representative or visit our website for more specific 

recommendations regarding pumps, filters, pressure relief valves and approved equivalent equipment.  

It is critical to adhere to the outlined hydraulic wet kit specifications.  Failure to follow the guidelines 

concerning required operation pressures can lead to system failure due to excessive heat buildup.

Please review the entire manual before operating the KEITH

®

 

WALKING FLOOR

®

 system.  If you have 

any questions, please call 541-475-3802 or email [email protected] where our support team 

will happily assist you.

Thank you again for putting your trust in our company!

Sincerely,

R. Mark Foster
President

DOC06344   Rev A

Summary of Contents for LeakProof III



















Reviews: