Keith LeakProof III Owner'S Manual Download Page 7

OWNER / OPERATOR MANUAL 

LeakProof III

        

 

 

 

 

 

DOC06436  Rev B

1.0  Safety

WARNING:  The large forces exerted by the floor when moving can result in damage to 

equipment which may result in serious injury or death. Always ensure that this manual has been 

read and fully understood by the operator. We advise that the operator keeps this manual with 

the vehicle at all times. Always ensure that ‘best practice’ is employed when using our systems. 

If in any doubt do NOT use this equipment and seek further assistance from your company’s 

safety officer. 

!!CAUTION!!

To Prevent Possible Injury or Death

1. 

DO NOT Operate the floor with the doors closed.

2.  DO NOT Stand behind the trailer or in the discharge area.
3. 

DO NOT Make adjustments to the unloading mechanism with the floor operating.

4.  DO NOT Operate the unloader when protective covers and screens are not in place.
5.  DO NOT Go underneath the trailer.
6.  DO NOT Leave the trailer unattended while the unloader is in operation.

ALWAYS:

1.  Disconnect the trailer from the hydraulic power unit (P.T.O.) before service and  maintenance.
2. 

Shut off the power supply before going underneath the trailer.

3.  Stay away from any oil leaks when hydraulic pressure is high.
4. 

Shut off the hydraulic power take off unit (P.T.O.) before moving the trailer.

!!Keep your hands, body parts and loose clothing away from the floor slats

and drive mechanism when the unloading system is in operation!!

Summary of Contents for LeakProof III



















Reviews: