background image

Keiser M3 Indoor Cycle Warranty Terms

The Keiser M3 Indoor Cycle is warranted to the original purchaser, to be free from defects in materials and workmanship.

Not Covered Under Warranty

- Loss caused by accident, abuse, improper use or neglect.

- Improper maintenance.

- Improper assembly by the purchaser.

- Failure to follow instructions as stated in any of the manuals provided with the

Keiser M3 Indoor Cycle.

The warranty terms begin with the date of original delivery to be evidenced by appropriate shipping documents. Any 

alteration of the equipment so listed without express written consent of Keiser shall constitute a waiver by the buyer of 

this warranty. This warranty does not cover other brand name products distributed, but not manufactured by Keiser, which 

are subject to their respective manufacturers warranties. During the warranty period, warranted defects will be repaired at 

Keiser, Fresno California, or the defective part will be replaced, at the option of the manufacturer, without charge for either 

parts or labor to repair the defective part.

This warranty does not cover the removal of the defective part and installation of the repaired part. All claims under the 

warranty must be in writing and authorization obtained from the manufacturer, Keiser, to return the defective parts for 

exchange. Defective parts must be returned to Keiser. The customer is responsible for all transportation costs on returned 

items to and from the point of manufacture. 

Users, agents, or anyone directing the use of said equipment shall determine the suitability of the product for its intended 

use, and said parties are specifically put on notice that they shall assume all risk and liability in connection herewith. The 

foregoing warranties are in lieu of and exclude all other warranties not expressly set forth herein, whether expressed or 

implied by operation of law or otherwise, including but not limited to any implied warranties of merchantability or fitness. 

Keiser shall in no event be liable for incidental or consequential losses, damages or expenses in connection with exercise 

products. Keiser’s liability hereunder is expressly limited to the replacement of parts not complying with this warranty or, 

at Keiser’s election, to the repayment of an amount equal to the purchase price of the parts in question. Keiser is not 

responsible for labor charges incurred in the replacement of defective parts. Keiser may, at its discretion, require the 

return of all defective parts. The customer is responsible for all transportation costs on warranted items to and from the 

point of manufacture. Replacement products are warranted for the balance of the original warranty period. 

All Keiser equipment sold by Keiser distributors, dealers, or salespeople must be registered for warranty purposes. The 

warranty registration form must be filed within 7 days of the sale or installation. Keiser equipment exported out of the US 

or Canada will be void of warranty unless purchased directly through a Keiser international distributor or dealer in the 

country of installation, or direct from Keiser’s international division.

22

Summary of Contents for M3



































Reviews: