Kedacom IPC4X2 Series User Manual Download

Page: 26 / 112

HD Mini Dome Camera User Manual

Network

Go to

Settings > Network

to configure IP and Port, Access Protocol and Other Protocols.

4.1 IP and Port

4.1.1

LAN

Go to

Settings > Network > IP and Port > LAN

and configure network parameters,

including IP address, subnet mask, default gateway and etc.

Picture 4-1 LAN



IP Address Configuration

If selecting “IPV4”, the mode includes "Static” or “DHCP”. When selecting static

mode, you need to configure IP Address, Subnet Mask and Default Gateway

manually; when selecting DHCP mode, the system obtains IP address automatically;

Note:

When filling the IPV4 IP address, click “Test” to confirm if the address is

available.

If selecting “IPV6”, the mode includes “Manual” and “Automatically obtain”. Under

the “Automatically obtain” mode, the IPV6 address is distributed from server,

gateway o

r router. Under “Manual” mode, enter the IP address, subnet mask and

default gateway according to actual conditions.

MTU:

Maximum transmission unit, the maximum size of data packet transmitted

through TCP/UDP protocol, ranging 500 ~ 1500, by default 1500.

Summary of Contents for IPC4X2 Series

















































































































Search results

Summary of Contents for IPC4X2 Series

Reviews:

Related manuals for IPC4X2 Series

Brands by name

Popular brands

Kedacom IPC4X2 Series, User Manual

Search results

Summary of Contents for IPC4X2 Series

Reviews:

Related manuals for IPC4X2 Series

Brands by name

Popular brands