Kedacom IPC4X2 Series User Manual Download Page 15

Page: 15 / 112

HD Mini Dome Camera User Manual

3. Basic Functions

By web client, user can not only view live video, but also perform local snapshot and recording, configure

alarm linkage and etc. Some models may not support some of the following functions. Please subject to

actual devices and the client.

Note:



Functions of different models may differ somewhat, and the disabled button in the client means

the device does not support the function. Function described in this manual with

“*” means only

some models support this function.



Different models may differ a little in some functions. Please subject to actual interface.

3.1 Live View

Click “Live View” to enter the preview interface.

Picture 3-1 Live View

Click the hide button on the left to hide “PTZ Control”, “Preset” and “Image Adjustment”. Click again

to unfold them.

3.1.1

PTZ Control

Click

to show the following interface:

Summary of Contents for IPC4X2 Series

















































































































Search results

Summary of Contents for IPC4X2 Series

Reviews:

Brands by name

Popular brands

Kedacom IPC4X2 Series, User Manual

Search results

Summary of Contents for IPC4X2 Series

Reviews:

Brands by name

Popular brands