Kedacom IPC4X2 Series User Manual Download Page 104

Page: 104 / 112

Laser Thermal Optical PTZ Camera User Manual

100



Enable SSH Login: Select the checkbox to enable SSH login, which means

SSH service is enabled and you can login by SSH mode. Usually it's

unnecessary to enable when the camera works normally.



Enable HTTPS Login: Select the checkbox to enable HTTPS login, which

means HTTPS service is enabled and you can login by HTTPS mode.



Enable Unauthorized Login Locking: Select the checkbox to enable

unauthorized login locking, and configure illegal login retry times and illegal



Illegal Login Retry Times: Configure illegal login retry times, default being 6

times.



Illegal Login Lock Time: Configure illegal login lock time, default being 10

minutes.

Note: After enabling unauthorized login locking, when the configured locking

conditions occur, the user IP will be locked up.

Click “Save” to validate settings.

8.3 Time

Go to

Settings > System > Time

, and configure Device Time Zone, Device Time, Auto Time

Correction, NTP Clock Synchronization and DST. Configure parameters by actual requests

and click "

Save

" to validate setting.

Picture 8-9 Time setting

Summary of Contents for IPC4X2 Series

















































































































Search results

Summary of Contents for IPC4X2 Series

Reviews:

Brands by name

Popular brands

Kedacom IPC4X2 Series, User Manual

Search results

Summary of Contents for IPC4X2 Series

Reviews:

Brands by name

Popular brands