Kedacom IPC4X1 Series User Manual Download

Page: 43 / 48

High Speed Dome Camera

User Manual

5. Settings

Some models may not support some of the functions stated below. User operation is subject to the actual models and

clients.

5.1 Network Access

The Initial Configuration part has introduced how to modify parameters via IPCSearch to make camera access

to network. Camera accepts multiple methods (via Ethernet and PPPoE) to access to network. The following

will introduce how to configure camera network parameters through the web client.

5.1.1

Ethernet

Go to

Settings > Network > IP and Port > LAN,

as shown in the picture to configure IP Address, Subnet

Mask and Default Gateway.

Picture 5-1 LAN

5.1.2

*Positioning

Go to

Settings > Network > IP and Port > Positioning

. Check

“

Enable

” to obtain the geographic

coordinates of the device.

Mode

: Options include GPS, BDS and Mixed mode. BDS: China Beidou navigation satellite system; GPS:

Global Position System; Mixed mode: BDS + GPS.

Report-to-center Interval

: Interval of sending data to the platform, ranging 5-120s. User can configure

according to the change frequency of device geographic coordinates, 5s by default.

Speed unit

: The moving speed unit of the device, options including km/ h and mile/ h.

Current speed

: Current moving speed of the device.

Current position

: Current longitude and latitude info of the device.

Summary of Contents for IPC4X1 Series

















































Search results

Summary of Contents for IPC4X1 Series

Reviews:

Related manuals for IPC4X1 Series

Brands by name

Popular brands

Kedacom IPC4X1 Series, User Manual

Search results

Summary of Contents for IPC4X1 Series

Reviews:

Related manuals for IPC4X1 Series

Brands by name

Popular brands