KE2 EvapOEM Troubleshooting Manual Download Page 3

Q.1.61 January 2023

Page 3

KE2 Evap

OEM

Alarm Troubleshooting Guide

© Copyright 2023 KE2 Therm Solutions, Inc., Washington, Missouri 63090

21214V3.0

Alarms & Notifications List

Alarm Type

Abbreviation

Scrolling Text*

Full Name

Description

Page

KE2 Combo 

Display

dtS

dtS

DOOR TEMP SENSOR

Door Temp Sensor Alarm Combo Display Aux 1 Door Temp Sensor is shorted or open.

Page 13

dt2

dt2

DISPLAY AUX2 SENSOR Disp Aux2 Sensor Alarm  Combo Display Aux 2 Temp Sensor is shorted or open.

Page 13

dt3

dt3

DISPLAY AUX3 SENSOR Disp Aux3 Sensor Alarm

Combo Display Aux 3 Temp Sensor is shorted of open.

Page 13

dtH

dtH

DOOR TEMP HIGH

High Door Temp Alarm

Combo Door Temp above Door Tempe High Door Alarm 

Offset longer than High/Low Door Temperature Alarm Delay.

Page 14

dtL

dtL

DOOR TEMP LOW

Low Door Temp Alarm

Combo Door Temp below Door Temperature - Low Door Alarm 

Offset longer than High/Low Door Temperature Alarm Delay.

Page 14

Hd2

Hd2

HIGH MONITOR TEMP2 High Mon2 Temp Alarm

Combo Aux2 Monitor Temp reading above Monitor Temp2 High 

Alarm setpoint longer than Monitor Temp2 Alarm Delay.

Page 15

Ld2

Ld2

LOW MONITOR TEMP2 Low Mon2 Temp Alarm

Combo Aux2 Monitor Temp reading below Monitor Temp2 Low 

Alarm setpoint longer than Monitor Temp2 Alarm Delay. 

Page 15

Hd3

Hd3

HIGH MONITOR TEMP3 High Mon3 Temp Alarm

Combo Aux3 Monitor Temp reading above Monitor Temp3 High 

Alarm setpoint longer than Monitor Temp3 Alarm Delay.

Page 15

Ld3

Ld3

LOW MONITOR TEMP3 Low Mon3 Temp Alarm

Combo Aux3 Monitor Temp reading below Monitor Temp3 Low 

Alarm setpoint longer than Monitor Temp3 Alarm Delay.

Page 15

EA1

EA1

DISPLAY EXTERNAL 

ALARM 1

Disp Ext1 Alarm

Combo External Alarm 1 input is active.

Page 15

EA2

EA2

DISPLAY EXTERNAL 

ALARM 2

Disp Ext2 Alarm

Combo External Alarm 2 input is active.

Page 15

EA3

EA3

DISPLAY EXTERNAL 

ALARM 3

Disp Ext3 Alarm

Combo External Alarm 3 input is active.

Page 15

Pbt

Pbt

HELP

Panic Button Alarm

 KE2 Combo Display panic button is active.

Page 15

LPCO (Low 

Pressure Cut-Out 

control) Only

Pdt

Pdt

PUMPDOWN TIMEOUT Pump Down Timeout

Low Pressure Cut-out Time exceeded before suction pressure 

reached Low Pressure Cut-out.

Page 15

SCC

SCC

SHORT COMP CYCLE

Short Compressor Cycle

Compressor started excessive number of times due to high 

suctionpressure in off mode, or comp. stopped excessive number 

of times due to low suction pressure while in refrigeration mode. 

Page 15

LPA

LPA

LOW PRESSURE

Low Pressure Alarm

Suction pressure below Low Pressure Cut-out despite attempts 

to run. 

Page 16

KE2 Humidity 

Control

HSA

HSA

HUMIDITY SENSOR

Humidity Sensor Alarm

Humidity sensor is shorted or open.

Page 16

HHA

HHA

HIGH HUMIDITY

High Humidity Alarm

Humidity reading above Humidity Se Humidity 

Differ Humidity Alarm Offset for longer than Humidity 

Alarm Delay.   

Page 16

LHA

LHA

LOW HUMIDITY

Low Humidity Alarm

Humidity reading below Humidity Setpoint - Humidity 

Differential - Humidity Alarm Offset for longer than Humidity 

Alarm Delay.

Page 17

CHA

CHA

HUMIDITY COMM

Humidity Comms Alarm

KE2 Evap OEM lost communication with KE2 Humidity Control 

board for 10 seconds.

Page 17

KE2 Evap OEM w/ 

High Side Control 

Only

HDA

HDA

HIGH DISCH TEMP

High Disch Temp

Discharge temp reading above High Dis charge Temp Set point for 

longer than High Discharge Temp Delay.  

Page 17

LCT

LCT

SYSTEM LOCKOUT

Comp Locked Out

In one hour system cycled off on high discharge temp more times 

than Max Num ber of Starts setpoint.  

Page 17

HCA

HCA

HIGHCOND TEMP

High Cond Temp

Condenser temp reading is above Cond Temp Se High 

Cond Temp Alarm Offset for longer than High Cond Temp Delay.   Page 18

LCA

LCA

LOW COND TEMP  

Low Cond Temp 

Condenser temp reading is less than Cond Temp Setpoint - Low 

Cond Temp Alarm Offset for longer than Low Cond Temp Alarm 

Delay.  

Page 18

A1A

A1A

AUX1 SENSOR

Dis Aux1 Sensor

Discharge temp sen sor input is shorted or open. 

Page 18

A2A

A2A

AUX2 SENSOR

Dis Aux2 Sensor

Discharge temp sen sor input is shorted or open. 

Page 18

A3A

A3A

AUX3 SENSOR

Dis Aux3 Sensor

Discharge temp sen sor input is shorted or open.  

Page 18

Summary of Contents for EvapOEM



















Reviews: