KBL megaSun pureEnergy 5.0 Operating Instructions Manual Download Page 41

Page: 41 / 48

O p e r a t i n g I n s t r u c t i o n s

megaSun pureEnergy 5.0

System messages

ERROR MESSAGES

After the error has been eliminated, all error messages must be acknowledged by pressing

START

on the interior

display.

No.

Status message

Description

Remedy

Excess

temperature

bimetal

Bimetal switch triggers.

Check the air-intake/air-discharge system. Let
the device cool down.

Maximum tanning time!

Enabling signal from coin-box system
comes in longer than the time value
approved under “Maximum tanning
time” (voltage remains connected)

Disconnect from the coin-box system.

Excess

temperature

exhaust fan!

Bimetal switch in the fan triggers.

Make sure the fan runs freely. Check the air-
intake/air-discharge system. Let the device cool
down.

KBL7 Hardware error
Input-Controller

Mainboard defective.

Contact your Customer Service.

Maximum

write

cycle

ﬂ ash memory reached

Maximum write cycle ﬂ ash memory
reached.

Contact your Customer Service.

Error! SD card read error
(CRC fault)

Update via SD card failed (CRC fault).

SD card check / replace.

Error! no access to the
SD card

Update via SD card failed (access
error).

SD card check / replace

Parameter storage not
found, please connect
and restart

Parameter storage not found, please
connect and restart.

Check connector parameter storage. If neces-
sary replace parameter storage.

Parameter storage no
valid serial number

Parameter storage no valid serial
number.

Contact your Customer Service.

CAN-BUS: Interior dis-
play V1 is incompatible

CAN-BUS operators incompatible.

Use CAN-BUS operaters V2.

CAN-BUS:

preSe-

lection display V1 is
incompatible

CAN-BUS: audio module
full V1 is incompatible

CAN-BUS: RGB module
V1 ist incompatible

Parameter storage write
error

Parameter storage write error.

Check connector parameter storage. If neces-
sary replace parameter storage.

Parameter storage read
error

Parameter storage read error.

Check connector parameter storage. If neces-
sary replace parameter storage.

Frequency

detection:

detection failed!

Frequency detection failed.

Restart the controller. Contact your Customer
Service after the third unsuccessful restart.

Frequency

detection:

power supply connection
faulty (connector X6/E6)!

Frequency detection failed. No mains
voltage.

Check mainboard connector X6/E6.

Summary of Contents for megaSun pureEnergy 5.0

















































Search results

Summary of Contents for megaSun pureEnergy 5.0

Reviews:

Related manuals for megaSun pureEnergy 5.0

Brands by name

Popular brands

KBL megaSun pureEnergy 5.0, Operating Instructions Manual

Search results

Summary of Contents for megaSun pureEnergy 5.0

Reviews:

Related manuals for megaSun pureEnergy 5.0

Brands by name

Popular brands