Kaysun COMPAK KHP 15/190 ACS1, Installation & Owner'S Manual

Page: 11 / 24

3.3 Electric Connection
3.3.2 Specifications of Power Supply
Table3-2
COMPAK KHP 15/190
ACS1
220-240V
̚
50Hz
CAUTION
Model Name
Power Supply
The power supply should be an independent circuit with rated
voltage.
Power supply circuit should be earthed effectively.
MIin. Diameter of Power
4
Supply Cord(mm 2
)
The wiring must be performed by professional technicians in
accordance with national wiring regulations and this circuit
diagram.
Earth Cord(mm
2
)
4
Manual Switch(A) Capcity/Fuse
A 30/25
An all-pole disconnection device which has at least 3mm
separation distance in all pole and a residual current
device(RCD)with the rating of above 10mA shall be
incorporated in the fixed wiring according to the national rule
Creepage Breaker
30 mA ≤0.1sec
Please choose the power cord according to above table, and
it should comply with local electric standard.
Set the electric leakage protector according to the relevant
electric technical standards of the state.
The power cord model, recommended power cord mode is
H05RN-F.
The power cord and the signal cord shall be laid out neatly
and properly without mutual interference or contacting the
connection pipe or valve.
When wiring the power supply, please add additional insulation
sheath at the place without rubber insulation layer.
After wire connection, check it ag ain and make sure the
correctness before power on.
WARNING
The unit must be installed with an
Creepage Breaker
near the power
supply and must be effectively earthed.
3.3.1 Electric Wiring Illustration
TP TH T4 T3 T5U T5L
Model selection
Without Electric Heater With Electric
Heater Item Content
Fan capacity
Terminal base
Transformer
Connected wires inside
of the tank
Zero-phase electricity
mutual inductor
AC mutual inductor
Relay connecting wires
Relay
Without
Disinfect With Disinfect
White
Short Wiring
CN5
Black
Model selection (User never allow to alter the
factory settings)
300L model 190L model
CN16 CN18 CN24 CN19 CN20 CN40
Reserve function Reserve function
T3 Evaporator temperature sensor
Ambient temperature sensor
Tank temperature sensor(Upper)
Tank temperature sensor(Lower)
SW3
CN28
T4
QUERY
T5U
Temperature protective
switch
SW4
FORCE
T5L
TP
CN6
Electric heater of
the tank
Mid terminal base
Main control
panel
Discharge temperature sensor
Suction temperature sensor
High Pressure Protection Switch
Automatic temperature
recovery switch
ELECTRIC EXPANSIVE
VALVE
TH
CN11
PRO-H
CN11
LCD display
panel
CN17
EEV
CN4
COMP
RY1
E-HEAT
RY3
Blue
Red
CT2 CT1
CN1
CN8 CN29 CN9
Red
Red
Yellow/gre
en
8
Brown Brown
Brown
Brown
6
Black
Black
The L, N wires, which get through the
zero-phase electricity mutual
inductor,
must keeping the same direction
during
wring, otherwise, system malfunction
may caused.
Blue
4
White
Red
4 Way
2
FAN Yellow/gre
en
Blue
Red
Yellow/gre
en
Black
Yellow/gre
en
Blue Brown
R
Red Black
E-HEAT Yellow/gree
n White
Blue
Red
Switch
Wiring diagram of tank
inside
Blue
Black
Compressor
capacitor
Black
If switch is
closed,
the unit will be stopped
forcibly.
If switch breaks,the unit can
run
normally according settings.
Power supply
1A/1B wire comes out from tank, must connect with the corresponding
component.
Fig.3-11
T5L: Tank Temp. Sensor (lower)
TP: Discharge Temp. Sensor
TH: Suction Temp. Sensor
T3: Evaporator Temp. Sensor
T4: Ambient Temp. Sensor
T5U: Tank Temp. Sensor (upper)
Earthing
Installation & Owner‘s Manual
7