Kayden CLASSIC Series, Product Manual

Page: 52 / 104

42
kayden.com Online Store
CLASSIC
®
800 Product Manual
Setup & Operation
Order, Model & Serial Number :
Process Media / Phase :
(E.g. Water/Liquid, Propane/Gaseous)
Fluid Velocity m/s (ft/s) :
Operating Temperature °C (°F) :
(Typical Process Temperature)
Install Date (dd/mm/yyyy):
 
Relay 1
LED NON-FLASHING
First 6 LEDs
Energize lower than set point
Last 6 LEDs
Energize higher than set point
Relay 2
LED NON-FLASHING
First 6 LEDs
Energize lower than set point
First 6 LEDs
Energize lower than set point
Fault
LED NON-FLASHING
First LED
Fail Low at 3.0 Ma’s
Last LED
Fail Low at 21.0 Ma’s
Set Point 1
LED NON-FLASHING
Set Point 1 Setting
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Set Point 2
LED NON-FLASHING
Set Point 2 Setting
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Bypass
LED NON-FLASHING
Bypass Time Amount. Each LED Represents 5 Seconds
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Relay 1
FLASHING
Heater Power Percentage
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Relay 2
FLASHING
Modbus Address Appears to the Right (can be multiple LEDs)
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Fault
FLASHING
First 6 LEDs
Forward Acting
First 6 LEDs
Reverse Acting
Set Point 1
FLASHING
State which LED is illuminated
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Set Point 2
FLASHING
State which LED is illuminated
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Mark an ‘X’ or state which LED(s) are illuminated between 0-100
LEDs on 1st Toggle
State which LED(s) is illuminated
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
LEDs on 2nd Toggle
State which LED(s) is illuminated
0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100
Front Display
Relay 1 Relay 2 Fault Set Point 1 Set Point 2 Run Mode Bypass
X, O or Blank
Device Info
Device Info
Fault Code
Mark an ‘X’ or state which LED(s) are illuminated between 0-100
Kayden Setting & Configuration Log Sheet
Configuration & Setting Information
Record Fault Code
Kayden Setting & Configuration Log Sheet