Kauo Heng KH-300 Operation Manual Download Page 5

Page: 5 / 70

KAUO HENG

COMPUTERIZED FLAT KNITTING MACHINE

3. Installation / Environmental conditions

Please install the machine as below instructions, in order to use and keep

this machine good working condition.

Do not install the machine at a place subject to direct
sunshine and/or adjacent to a heat generation source
such as a furnace/oven.

Do not install the machine at a place subject to rapid
temperature changes.
The temperature should be 0

℃

~ 35

℃

Do not install the machine at a place where there is a
lot of dust and dirt, or a location affected by chemical
gases, sea breeze etc.

Do not install the machine at a place subject to
excessive moisture.
The humidity should be 30 ~ 80%.

Do not install the machine on a slope or unstable place.

Please connect the electric power and make sure the
ground wire is connected correctly.

KH-300

OPERATION MANUAL

Summary of Contents for KH-300







































































Search results

Summary of Contents for KH-300

Reviews:

Related manuals for KH-300

Brands by name

Popular brands

Kauo Heng KH-300, Operation Manual

Search results

Summary of Contents for KH-300

Reviews:

Related manuals for KH-300

Brands by name

Popular brands