manualshive.com logo in svg

Kathrein MSK 140/OHD, Instructions For Use Manual, Page: 22 / 76

Share
Download
Kathrein MSK 140/OHD Instructions For Use Manual Download Page 22

 

Changing Basic Parameters

22 von 76

13 

Changing Basic Parameters

Using the volume menu, it is possible to change the 
following settings in the signal meter:

 

●

VOLUME

 

●

BRIGHTNESS

 

●

VIDEO IN 

(video 

input)

 

●

RF IN

 

●

BATTERY SAVING

 

●

CONFIGURATION MENU

13.1 

Changing the Volume

1.  Press 

VOL CONFIG

 to open the volume menu.

 

➯

The volume menu opens.

1.  Press the rotary wheel.

 

➯

The 

VOLUME

 parameter is active (highlighted blue).

2.  Press the rotary wheel to go to the volume.

 

➯

The volume is active (highlighted blue).

3.  Turn the rotary wheel to change the volume.
4.  Press the rotary wheel to save the selection.

 

➯

The volume is saved. The 

VOLUME

 parameter is active (highlighted blue).

13.2 

Changing the Brightness

1.  Press 

VOL CONFIG

 to open the volume menu.

 

➯

The volume menu opens.

2.  Press the rotary wheel.

 

➯

The 

VOLUME

 parameter is active (highlighted blue).

3.  Turn the rotary wheel to select 

BRIGHTNESS

.

 

➯

The 

BRIGHTNESS

 parameter is active (highlighted blue). 

4.  Press the rotary wheel to select the brightness value.

 

➯

The brightness value is active (highlighted blue).

5.  Turn the rotary wheel to change the brightness value.
6.  Press the rotary wheel to save the selection.

Summary of Contents for MSK 140/OHD













































































Reviews:

No comments