background image

47 / 72

Allowing the door to swing
back and forth can cause acci-
dents.

Always

secure

the

open door with the door hand-
le. Never drive with an open
door. Secure the door before
departure.

To fix the door in the open po-
sition, pull the rear door faste-
ner from a point close to the
exit while bringing the door re-
taining pin to the open posi-
tion. This will both allow the
pin to come out more easily
and prevent it from being
damaged.

Be careful not the squeeze
your hand between the door
and the side panel.

In trailer models, different door fixing ele-
ments can be used according to the cus-
tom-er's request. (1,2)

Fixing the door

Fixing the door

4.4. Side panel

Your vehicle has insulated side panels
made of sandwich panels.

Side panel

There may be extra protection plate (1)
on the side panel to prevent the door
from hitting the GRP.

Side panel protection plate

4.5. Pillars

Two different types of pillars are used in
vehicles.

Rear pillars

Front pillars

4.5.1. Rear Pillars

There is a single-piece rear frame made
of stainless steel at the rear of the
vehicle.

Summary of Contents for Reefer 2023 Series









































































Reviews:

Related manuals for Reefer 2023 Series