Karel MS38s Programming Manual Download Page 64

Page: 64 / 78

Karel MS38s Programming Guide
Edition 3.1

II. REMOTE PROGRAMMING

II.1.

REMOTE PROGRAMMING ENTRY (# 3828 or # 3748)

#3828 or #3748

When the operator is talking to the technician, the operator must use one of these
codes to enable the system for

Remote Programming

. After entering the

Remote

Programming

, the operator should hang up.

•

OTES

1. After

Remote Programming

is initiated, the technician starts hearing a

special discontinuous dial tone and keeps on hearing this tone after each
successful entry of a program or feature code.

2. If the technician fails to make a successful entry of a program or feature

code, he starts receiving error tone. In such a case, he can refresh the
discontinuous dial tone by pressing “ ”

key.

II.2.

REMOTE PROGRAMMING EXIT

(829 or 749 / #)

Allows exiting

Remote Programming

either by the operator or by the technician.

829 or 749

(to be entered by the operator)

(to be entered by the technician)

•

OTES

The system automatically releases the

Remote Programming

line, in case the

technician does not enter any code for longer than 5 minutes.

Summary of Contents for MS38s















































































Search results

Summary of Contents for MS38s

Reviews:

Brands by name

Popular brands

Karel MS38s, Programming Manual

Search results

Summary of Contents for MS38s

Reviews:

Brands by name

Popular brands