Karel MS38s Programming Manual Download Page 20

Page: 20 / 78

Karel MS38s Programming Guide

Edition 3.1

II.15.

PARALLEL OPERATORS

(8085/8086)

Allows defining extensions to ring in parallel with the operator for the incoming
external calls.

•

CTIVATE

•

ANCEL

8085 E

8086

•

ARAMETERS

E :

Extension

number.

•

EFAULT

Parallel Operators

are

defined.

•

OTES

1. At most 4 different

Parallel Operators

can be entered. If more than 4

Parallel Operators

are to be entered, error tone is received after dialing

“

8085

”.

2. If

Parallel Operator

is busy when there is an incoming external call, the

next extension in his

PBX Group

program does not ring in parallel with the

operator.
However, if the operator is busy when there is an incoming external call,
the incoming external call rings on the next extension in the operator’s

PBX Group

, but not on the

Parallel Operators

3. Even

Parallel Operator

activates

Follow Me

facility, incoming external

calls still ring on this

Parallel Operator

but not on the

Follow Me

extension.

However, if the operator activates

Follow Me

facility, incoming external

calls ring on the

Follow Me

extension, but not on the

Parallel Operators

4. If the operator or the

Parallel Operators

activate

Follow Me (No Answer)

facility, the incoming external calls are not diverted to

the Follow Me (No

Answer)

extensions.

Parallel Operators

cannot use

Parallel Extension Enable

facility.

6. If

“

8086

” is dialed to cancel, then all

Parallel Operators

are cleared.

7. Once

Parallel Operator

is defined, it will be automatically enabled.

Summary of Contents for MS38s















































































Search results

Summary of Contents for MS38s

Reviews:

Brands by name

Popular brands

Karel MS38s, Programming Manual

Search results

Summary of Contents for MS38s

Reviews:

Brands by name

Popular brands