![background image](http://html1.mh-extra.com/html/karcher/km-120-250-r-bp/km-120-250-r-bp_manual_3732167023.webp)
-
9
Note
: The sweeping track is factory-set to
80 mm; it is steplessly adjustable if the
brush roller wears down.
Check tyre pressure.
Switch off suction blower.
Drive sweeper on to a smooth, even
surface covered with a visible layer of
dust or chalk.
Roller brush and side brush control le-
ver (1) backwards: Switches the roller
brush on.
Roller brush control lever (3) back-
wards: Lowers the roller brush.
Allow the roller brush to run for approx.
10 seconds.
Roller brush and side brush control le-
ver (1) to middle position.
Roller brush control lever (3) forwards:
Raises the roller brush.
Raise waste container.
Drive machine backwards.
Check sweeping mirror.
The sweeping track should have an even
rectangular shape which is 80-85 mm wide.
Undo and adjust the stop screw for
wear adjustment (12).
Stop screw at the top: narrow sweeping
area.
Stop screw at the bottom: broad sweep-
ing area.
Tighten the stop screw again.
Check the sweeping area of the roller
brush again as described.
The side-brushes lift up.
Drive sweeper on to a smooth, even
surface covered with a visible layer of
dust or chalk.
Lower the side brushes using the con-
trol lever and allow them to run for ap-
prox. 10 seconds.
The side-brushes lift up.
Drive machine backwards.
Check sweeping mirror.
The width of the sweeping track should lie
between 40-50 mm.
Set the sweeping track using the two
adjusting screws.
Check sweeping mirror.
DANGER
Risk of injury! Always apply the safety bar
when the waste container is raised.
Drive the waste container up and se-
cure it with the safety rod.
Fold the safety rod for the high empty-
ing up and insert it into the holder (se-
cured).
1 Holder of safety rod
2 Safety rod
Open the side cover as described in
Chapter "Replace brush roller".
Release the 6 wing nuts on the side
holding plate.
Loosen 3 nuts (SW 13) on the front
holding plate.
Press the side seal down (elongated
hole) until it is about 1 to 3 mm to the
floor.
Screw in the holding plates.
Repeat the procedure on the other side
of the appliance.
Switch on manual filter shake off.
몇
WARNING
Risk of injury!
Wear a dust mask when working
around the dust filter. Observe safety
regulations on the handling of fine parti-
cles.
Clean the dust filter with the filter clean-
ing button.
Empty waste container.
1 Lock of appliance hood
2 Cover
3 Filter cover
Open the lock, remove the star grip
screw to do this.
Fold cover forwards.
1 Lock, filter cover (2x)
2 Filter cover
Open the lock.
Open filter cap.
1 Cross struts
2 Dust filter
Check the dust filter, clean or replace if
necessary.
Check and adjust roller brush sweeping
track
Check and adjust sweeping track of the
side-brush
Adjust the side seals
Manually clean the dust filter
Check/replace dust filter
2
1
23
EN
Summary of Contents for KM 120/250 R Bp
