background image

Operating Instructions

English

35

Warranty

The warranty terms and conditions issued
by our responsible sales company apply in
every country. Within the warranty period,
any faults in the unit will be rectified free of
charge provided that the problem was
caused by a material defect or
manufacturing error.

The warranty only applies if the dealer fills
in, stamps and signs the enclosed reply
card when the unit is sold and the
purchaser then returns it to the appropriate
local distributor.

In the event of a warranty claim, please
contact your dealer or the nearest
authorised After-Sales Service office and
produce both accessories and proof of
purchase.

General notes

Safety features

Overflow valve with two pressure
switches

 When reducing water volume at pump

head or with the servopress control, the
overflow valve will open and part of the
water will flow back to the pump suction
side.

 If the handgun is closed off so that all

the water flows back to the pump suction
side, the pressure switch at the overflow
valve turns off the pump.

 Reopening the handgun causes the

pressure switch at the cylinder head to
switch the pump back on again.

The overflow valve is set at the factory and
lead-sealed. Adjustment can only be made
by After-Sales Service.

Safety valve

 The safety valve opens if the overflow

valve or pressure switch is defective.

The safety valve is set at the factory and
sealed. Adjustment can only be made by
After-Sales Service.

Low water protection

 The low water protection prevents the

burner switching on when water is
insufficient.

 A strainer prevents dirt accumulation on

the protection and must be regularly
cleaned.

Motor protection switch

 The motor protection switch interrupts

the circuit should overloading occur.

Switching on procedures

 Switching on procedures generate brief

voltage drops.

 Impairments of other appliances can

occur in cases of unfavourable mains
conditions.

 No problems are to be expected with a

mains impedance of less than 0,15 ohm.

Summary of Contents for HDS 995 MX Eco
























Reviews: