background image

Operating Instructions

English

29

Operation with hot water

 Warning!

Danger of scalding

!

  Set the remperature regulator (item 24)

to the required temperature

We recommend the following cleaning
temperatures

 Slight contamination 30-50°C

 Protein soiling, e.g. in foodstuffs industry

max. 60°C

 Motor vehicle cleaning, machine

cleaning 60-90°C

Safety deactivation

If the handgun is not opened or closed for
more than 30 minutes, for safety reasons
the pump switches off automatically.

 To switch it on again turn the main

switch to "0" and then back to "I".

(EPROM without shut down 6.682-595
available from service)

Operation with steam

 Danger: Steam!

At operating temperatures above 98°C
operating pressure must not exceed 32 bar
(HDS 1295: 28 bar).
Therefore the following steps must be
taken without fail:

!

  Replace high-pressure nozzle by steam

nozzle

Manufacture no.:
4.766-023

HDS 995

4.766-024

HDS 1295

!

  Fully open water delivery control at the

handgun, in the + direction to the stop.
See Figure 9 (B)

!

  Set operating pressure to minimum

value. See Fig. 10

!

  Set the temperature regulator (item 24)

to min. 100°C

 Danger: Steam!

Danger of scalding!

We recommend the following cleaning
temperatures

 Preservative removal, extremely greasy

dirt 100-110°C

 Thawing of aggregates, certain facade

cleaning operations up to 140°C

After every operation

 Warning!

Danger of scalding with hot water.
After operating it with hot water or steam, to
cool it the unit must be operated at least
two minutes with cold water with an open
handgun.

Following operation with cleaning agent

!

  Set cleaning agent metering valve

(item 31) to "0"

!

  Set unit switch (item 23) to "I"

!

  Actuate handgun and flush unit for

approx. 1 min

Stopping machine

!

  Set unit switch (item 23) to "0"

!

  Shut off water supply

!

  Switch the pump briefly on with the unit

switch (item 23) (approx. 5 sec.)

!

  Remove mains plug from socket ONLY

with dry hands

!

  Remove water connection

!

  Actuate handgun to depressurise unit

!

  Put on safety of handgun Figure 9 (A)

!

  Engage spray lance in cover holder

Summary of Contents for HDS 995 MX Eco
























Reviews: