background image

9.800-103.0  •  REV. 1/07

5

 

 PRESSURE 

W

ASHER  

  

OPERA

TOR’S MANU

AL

  

IMPORTANT SAfETy INfORMATION

  8.  High pressure developed by these machines will 

cause personal injury or equipment damage. Use 
caution when operating. Do not direct discharge 
stream  at  people,  or  severe  injury  or  death  will 
result.

WARNING: High pressure spray 
can cause paint chips or other 
particles  to  become  airborne 
and fly at high speeds.

  9.   Eye  safety  devices,  safety 

clothing  and  foot  protection 
must  be  worn  when  using 
this equipment.

10.   Never make adjustments on 

machine  while  it  is  in  op-
eration.

WARNING: Spray gun kicks back. Hold with both 
hands.

  11. Grip cleaning wand securely with both hands be-

fore starting the cleaner. Failure to do this could 
result in injury from a whipping wand.

 12. Machines with spray gun should not be operated 

with the spray gun in the off position for extensive 
periods of time as this may cause damage to the 
pump.

 13. The  best  insurance  against  an  accident  is  pre-

caution and knowledge of the machine.

 14. Manufacturer  will  not  be  liable  for  any  changes 

made to our standard machines, or any compo-
nents not purchased from manufacturer.

WARNING:  Keep  wand,  hose 
and  water  spray  away  from 
electric  wiring  or  fatal  electric 
shock may result.

15.   Read  engine  safety  instruc-

tions provided.

16.   Never run pump dry or leave 

spray gun closed longer than 
5 minutes.

 17. Inlet water must be cold and clean fresh water.
 18. Use No. 1 or No. 2 Heating Oil (ASTM D306) only. 

NEvER 

use gasoline in your fuel oil tank. Gasoline 

is more combustible than fuel oil and could result 
in a serious explosion. 

NEvER 

use crankcase or 

waste oil in your burner. Fuel unit malfunction could 
result from contamination.

 19. Do not confuse gasoline and fuel oil tanks. Keep 

proper fuel in proper tank.

 20. Protect machine from freezing.
 21. Be  certain  all  quick  coupler  fittings  are  secured 

before using pressure washer.

 22. Do not allow acids, caustic, or abrasive fluids to 

pass through the pump.

 23. To reduce the risk of injury, close supervision is 

necessary when a product is used near children. 
Do  not  allow  children  to  operate  the  pressure 
washer. 

This  machine  must  be  attended  dur-

ing operation.

 24. Do not operate this product when fatigued or under 

the influence of alcohol or drugs. Keep operating 
area clear of all persons.

 25. Protect  discharge  hose  from  vehicle  traffic  and 

sharp objects. Inspect condition of high pressure 
hose before using or bodily injury may result.

 26. Before disconnecting discharge hose from water 

outlet, turn burner off and open spray gun to al-
low water to cool below 100°F before stopping the 
machine. Then open the spray gun to relieve pres-
sure. Failure to properly cool down or maintain the 
heating coil may result in a steam explosion.

 27. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

 28. This  machine  must  be  attended  during  opera-

tion.

 29. 

CAUTION:  Risk  of  injury.  Disconnect  battery 
ground terminal before servicing.

PRE-OPERATION CHECk

 

 Pump oil (SAE 30W non-detergent oil, General)

 

 Cold water supply (6 gpm   58"   20 psi)

 

 Hose, wand, nozzle (nozzle size per serial plate)

 

 Engine fuel (unleaded 86 or higher octane)

 

 Engine oil (SAE 10W30)

 

 Burner fuel (No. 1 home heating fuel or diesel)

WARNINg

USE PROTECTIvE  

EyE WEAR 

AND CLOTHINg  

WHEN OPERATINg 

THIS EqUIPMENT.

WARNINg

kEEP WATER 

SPRAy AWAy fROM 

ELECTRICAL WIRINg.

Summary of Contents for HDS 4.0/32 Pe Cage













































Reviews: