background image

9.800-103.0  •  REV. 1/07

OPERA

TOR’S MANU

AL

   

PRESSURE 

W

ASHER 

 

4

INTRODUCTION & IMPORTANT SAfETy INfORMATION

Thank you for purchasing our Pressure Washer.
This manual covers the operation and maintenance of 
your pressure washer. All information in this manual 
is based on the latest product information available at 
the time of printing.
We  reserve  the  right  to  make  changes  at  any  time 
without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of 
the manufacturer’s operating instructions and warnings 
before using this pressure washer. Warning information 
should be emphasized and understood. If the operator 
is not fluent in English, the manufacturer’s instructions 
and warnings shall be read to and discussed with the 
operator  in  the  operator’s  native  language  by  the 
purchaser/owner, making sure that the operator com-
prehends its contents.
Owner and/or user must study and maintain for future 
reference the manufacturers’ instructions.

This manual should be considered a perma-
nent part of the machine and should remain 
with it if machine is resold.
When ordering parts, please specify model 
and serial number.

IMPORTANT SAfETy 

INfORMATION

WARNING: When  using  this  product  basic  pre-
cautions should always be followed, including the 
following:

CAUTION: To reduce the risk of 
injury,  read  operating  instruc-
tions carefully before using.

  1.   Read  the  owner’s  manual 

thoroughly.  Failure  to  follow 
instructions  could  cause  a 
malfunction  of  the  machine 
and  result  in  death,  serious 
bodily injury and/or property 
damage.

  2.  Know how to stop the machine and bleed pres-

sures  quickly.  Be  thoroughly  familiar  with  the 
controls.

  3.  Stay alert — watch what you are doing.
  4.  All  installations  must  comply  with  local  codes. 

Contact your electrician, plumber, utility company 
or the selling distributor for specific details.

WARNING: Risk of asphyxiation. 
Use this product only in a well 
ventilated area.

  5.   Avoid  installing  machines  in 

small areas or near exhaust 
fans.  Exhaust  contains  poi-
sonous  carbon  monoxide 
gas;  exposure  may  cause 
loss  of  consciousness  and 
may  lead  to  death.  It  also 
contains

    chemicals  known  in  certain  quantities,  to  cause 

cancer, birth defects, or other reproductive harm.

WARNING:  Flammable  liquids 
can create fumes which can ig-
nite, causing property damage 
or severe injury.
CAUTION:  Risk  of  fire.  Do  not 
add  fuel  when  the  product  is 
operating.

  6.   Allow engine to cool for 2 min-

utes  before  refueling.  If  any

    fuel is spilled, make sure the area is dry before 

testing the spark plug or starting the engine. (Fire 
and/or explosion may occur if this is not done.)

    Gasoline engines on mobile or portable equipment 

shall be refueled:
(a)   outdoors;
(b)   with the engine on the equipment stopped;
(c )  with no source of ignition, within 10 feet of the 

dispensing point; and

(d )  with an allowance made for expansion of the 

fuel  should  the  equipment  be  exposed  to  a 
higher ambient temperature.

    In an overfilling situation, additional precautions are 

necessary to ensure that the situation is handled 
in an safe manner.

WARNING: Risk of explosion – do not spray flam-
mable liquids.

   7.  Do not place machine near flammable objects as 

the engine is hot.

WARNING: Risk of injection or 
severe injury to persons - Keep 
clear of nozzle - Do not touch or 
direct discharge stream at per-
sons. This machine is to be used 
only by trained operators.
CAUTION:  Hot discharge fluid. 
Do not touch or direct discharge 
stream at persons.

RISk Of ExPLOSION: 

DO NOT USE WITH 

fLAMMAbLE LIqUIDS.

WARNINg

WARNINg

RISk Of 

ASPHyxIATION. USE 

THIS PRODUCT ONLy 

IN A WELL 

vENTILATED AREA.

WARNINg

HIgH PRESSURE 

STREAM CAN PIERCE 

SkIN AND TISSUES.

WARNINg

READ OPERATOR’S 

MANUAL 

 THOROUgHLy  

PRIOR TO USE.

CAUTION

Summary of Contents for HDS 4.0/32 Pe Cage













































Reviews: