![background image](http://html1.mh-extra.com/html/karcher/bd-60-95-rs-bp/bd-60-95-rs-bp_operating-instructions-manual_654476021.webp)
English
21
Î
Turn the vacuum lip or replace and in-
sert it back into the vacuum bar and
align.
Î
Replace pressure plate.
Î
First tighten the central wing bolt. En-
sure that the pressure plate is lying firm-
ly on the vacuum lip.
Î
Tighten the remaining wing bolts.
Î
Dismantle the vacuum bar.
1 Clamping lock
2 Strap
3 Vacuum lip
Î
Open the clamping lock and remove the
strap.
Î
Take out the vacuum lips.
Note
The vacuum lips can be turned thrice till all
edges are worn off. After that you need a
new vacuum lip.
Î
Turn the vacuum lip or replace and in-
sert it back into the vacuum bar and
align.
Î
Insert the strap and close the clamping
lock. The tension must just be sufficient
to hold the vacuum lip without wrinkling.
Adjust the clamping lock, as required.
1 Pipe
2 Sieve with floater ball
Î
Clean the sieve from the outside and
rinse it.
Î
Check the mobility of the floater ball.
If it is too dirty:
Î
Hold the pipe firmly and pull out the
sieve from the pipe.
Î
Clean sieve and ball.
Î
Hold the pipe firmly and reinsert the
sieve.
1 Splash guard
2 Cross-handle for spray guard
3 Bearing lid screw
4 Bearing lid
Î
Lift the cleaning head.
Î
Turn key to "0" and remove it.
Î
Loosen the cross-handle of the spray
guard and tilt the spray guard to the
side.
Î
Loosen the screw of bearing lid and pull
the upper end of the bearing lid up-
wards.
Î
Press the bearing lid downwards and
cross it.
Î
Pull the bearing lid from the brush.
Î
Pull out the brush.
Î
Insert new brush with the carrier in the
front into the cleaning head and push it
up to the end.
Î
Let the brush tilt downwards and insert
the bearing lid.
Î
Hook in the lower end of the bearing lid
at the cleaning head and push the bear-
ing lid upwards.
Î
Press the upper end of the bearing lid at
the cleaning head and tighten with
screw.
Î
Tilt back the spray guard and tighten the
cross-handle.
Î
Repeat process on the opposite side.
1 side spray guard
Î
Lift the cleaning head.
Î
Turn key to "0" and remove it.
Î
Raise the side spray guard and remove
it from the side.
Î
Turn the unlocking lever of the sliding
brush in an anti-clockwise direction - the
brushes will fall downward and can be
pulled outward at the bottom of the de-
vice.
Î
Hold the new brush under the cleaning
head.
Î
Turn the unlocking lever of the sliding
brush in clockwise direction and press
the brush upward.
Î
Release the unlocking lever and check
that the brush is sitting properly.
Î
Replace the spray-guard.
Î
Repeat process on the opposite side.
Î
Lower the cleaning head.
Î
Turn key to "0" and remove it.
BR model:
Î
Loosen the end and adjust it in such a
way that the rubber lip is bent sidewards
by approx. 9 to 10 mm.
BD model:
1 Stopper
Î
Loosen the end and adjust it in such a
way that the lower edge of the spray
guard is approx. 3 mm from the floor.
Î
Tighten the stopper.
1 Screw
2 Front panel
Î
Loosen screws.
Î
Remove front panel.
Turn/ replace rear vacuum lip
Cleaning the floater
Replacing the brush rollers
Replacing the Disk Brushes
Mount splash guard
Checking the drive chain
www.motralec.com / [email protected] / 01.39.97.65.10
Summary of Contents for BD 60/95 RS Bp
