25
ATTENTION
Risk of injuries!
In dangerous situations, release
the safety switch/drive lever.
Clean Water
→ Open the clean water tank cover.
→ Fill with clean water (maximum 60 °C)
to the lower edge of the filling nozzle.
→ Close the clean water tank cover.
ATTENTION
Damage risk.
Only use the recommended
detergents. With other detergents, the
operator has increased risk regarding
operational safety and risk of accidents.
Only use detergents that are free
from solvents, hydrochloric acid, and
hydrofluoric acid. Pay attention to the
detergent safety warnings.
Warning:
Do not use highly foaming detergents.
Recommended Detergents:
For any type of application, the
recommended detergent is:
Kärcher’s RM755.
→
Add the cleaning detergent to the clean
water tank.
Warning:
If the clean water tank is empty, the
cleaning head continues working without
liquid supply.
Setting the Water Quantity
→ With the water adjustment knob, adjust
according to the dirt on floor.
Warning:
Perform the first cleaning test with a small
amount of water. Increase water volume
step-by-step until the desired cleaning
result is achieved.
Setting the Suction Bar
To improve the vacuuming result on tiled
floors, the suction bar can be turned to an
oblique position of up to 5°.
→ Loosen the wing bolt.
→ Turn the suction bar.
→ Tighten the wing bolts.
Operation
Draining Waste Water
Filling Consumption Products
Tilting
If the vacuum result is unsatisfactory, the
suction bar tilting can be changed.
→
Adjust the rotary handle to tilt the
vacuum bar.
The transport caster* lifts the cleaning
head until it no longer contacts the ground.
The equipment is transported with the
lifted cleaning head.
1 - Transport caster in the “Transport”
position
2 - Transport caster in the “Cleaning/
operation” position
→ Select the desired caster position with
your foot.
* If equipped.
With the height adjustment, the bending
of the vacuum blades is influenced during
contact with the floor.
→ Adjust the height adjustment
rotary handles until you get the best
vacuuming result.
Cleaning
WARNING
Risk of damage to the floor. Do not operate
the device on the same spot for extended
periods.
→ Activate the program selection switch
according to the desired cleaning program.
→ Activate the brush drive switch with
both hands.
Lower the Suction Bars
→ Pull the lever out and press it down; the
vacuum bar is lowered.
Warning:
-
For cleaning tiled floors, set the
straight suction bar in such a way that
cleaning is not performed at an angle of
90 degrees to the joints.
-
The suction bar oblique position
and tilting can be adjusted to achieve
better vacuuming results (see “Setting the
Vacuum Bar”).
-
When the waste water tank is full,
the float closes the vacuum opening and
the vacuum turbine runs at an increased
rotation speed. If this is the case, shut
the vacuum off and empty the waste
water tank.
→ Close the water dosing knob.
→ Release the brush drive switch.
→ Put the program selection switch in the
vacuuming position.
→ Slightly move the device forward and
vacuum waste water.
→ Lift the suction bar.
→ Put the program selection switch in the
OFF position.
→ If necessary, charge the battery.
ATTENTION
Comply with local wastewater
treatment rules.
→ Remove the water drain hose from
the support and lower to a suitable
collection device.
→ Compress or bend the dosing device.
→ Open the dosing device cover.
→ Empty the water by pressing or bending.
→ Wash the waste water tank with
clean water.
→ Unscrew the clean water tank cover.
DANGER
Risk of injuries! The device may
only be operated for loading and
unloading on gradients up to the maximum
value (see “Technical Data”). Walk slowly.
CAUTION
Risk of personal injury or damage!
Pay attention to the device weight
during transport.
→ Activate the transport caster, if
equipped, — located on the right side of
the device — by pressing the pedal.
Height
Transport Caster
Transport
Stopping and Shutting Down
Detergent
Oblique Position
Draining Clean Water
WARNING
NOTE: The Suction hose must be
mounted outside of the suction bar lift le-
ver bracket. The hose must not be twisted.