manualshive.com logo in svg

Kanomax 3443, Operation Manual

Share
Download
Kanomax 3443 Operation Manual Download Page 42

4. Consumables Replacement 
 

 

36

4.2 Protective LCD Sheet Replacement 

When the protective LCD sheet becomes dirty or is damaged, replace it. 
 

<Preparing for replacement part> 

Prepare the provided protective LCD sheet for replacement or purchase the provided protective LCD sheet (3442-04). 
 

<Replacing protective LCD sheet> 

(1)

 

Remove the protective sheet that is to be replaced. 

(2)

 

Wipe out the dirt and dust on and around the LCD. 

(3)

 

Put the new protective sheet for replacement on the LCD.   

 

4.3. Rubber Protector Replacement 

When the rubber protector becomes dirty or is damaged, you can replace the rubber protector. 
 

<Preparing for replacement part> 

Purchase the rubber protector (3442-02). 
 

<Replacing rubber protector> 

(1)

 

Remove the AC adapter and output cable. 

(2)

 

Pull the instrument up to remove it from the rubber protector.   

(3)

 

Insert the instrument into the new rubber protector. For the insertion direction, refer to the picture below. 
Make sure that the top corners of the rubber protector are fit with the instrument. 

 
 
 

(2) Pull the instrument out 

from the protective cover. 

(3) Insert the instrument into 

the new protective cover. 

Make sure that the cleaning air 
vent side of the instrument and 
the logo on the rubber protector 
are facing the same direction. 

Summary of Contents for 3443



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands