manualshive.com logo in svg

Kanomax 3443, Operation Manual

Share
Download
Kanomax 3443 Operation Manual Download Page 11

2. Getting Started 
 

 

5

2.1.2 Setting AC Adapter

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

CAUTION

: Make sure to use the provided AC adapter (MODEL 6113-02). 

Other commercially available adapters may have different polarity and specifications, which could 
result in short circuit, fire or damage to the instrument. 

 

 

‹

Battery Level Indicator 

 
 
 
 
 
 
 
 
The below shows how the indicator changes as the battery runs low. 
 
 
 
 
 

<<Caution>> 

-

 

The remaining capacity of the battery is indicated in 10 levels. When “×” is displayed on the indicator, the 
remaining capacity of the battery is very low. Connect the provided AC adapter immediately or finish a 
measurement once and replace the batteries with new ones. 

-

 

When the batteries die, the display will be turned off and the power will also be off. 

<AC Adapter> 
MODEL 6113-02 
INPUT:  100 ~ 240 V 
OUTPUT: 9V/2A 
Polarity 

DC-in Jack for 
AC Adapter

 

Connect the supplied AC adapter into the DC-in 
Jack on the side of the main unit. When the AC 
adapter is connected, the power is supplied by 
the AC adapter. It is OK to leave batteries in the 
battery compartment. However, if the 
instrument is not used for a prolonged time, 
please remove the batteries to prevent the 
contact failure caused by corrosion of the 
battery. 

Battery level indicator is displayed on 
the upper right corner of the display. 

Summary of Contents for 3443



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands