Kaliburn SR-100i User Manual Download | Manualshive

Page: 3 / 75

background image

SR-100i User’s Manual

Limited Warranty

KALIBURN expressly warrants that this product shall be free from defects in
materials and workmanship, under proper and normal use for the intended
function of such equipment, for a period of one (1) year for the SR-100i torch and
leads and three (3) years for the SR-100i power supply. This product is intended
for commercial use and is not intended for personal, family, or household
purposes. There are no warranties that extend beyond the description on the face
hereof.

All other warranties, either expressed or implied, including any

implied warranty of merchantability or fitness for any particular purpose,
are expressly excluded.

If this product or any component thereof is determined to be defective in
manufacture, KALIBURN will repair or replace the defective component or
product. The buyer’s remedies are limited to the return of the product for repair
or replacement of any non-conforming product or part at the sole discretion of
KALIBURN. No freight charges of any kind are covered under this warranty.
All returned goods shall be at the buyer’s risk and expense. Beyond this remedy,
KALIBURN will not be responsible for any special, incidental or consequential
damages or injury to the person or property of anyone by reason of any defect in
any equipment sold hereunder.

This warranty will be considered void if torches or torch
consumables manufactured by anyone other than
KALIBURN are incorporated into this product.

Returned Goods Procedure

KALIBURN utilizes a returned goods procedure that must be followed before
returning any items for repair, replacement, or restocking. This means that a
returned goods authorization number must be obtained prior to shipment to
KALIBURN. It will be necessary for the customer to provide a description, along
with the stock number and serial number, if applicable, of the item to be returned.
In no case will KALIBURN accept a returned shipment without the proper
returned goods authorization number.

«
1
2
3
4
5
...
»

Summary of Contents for SR-100i












































































Reviews:

No comments

Related manuals for SR-100i

Brand: Harman Kardon Pages: 2

Brand: Happ Pages: 49

Brand: JBL Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 33

Brand: Magnavox Pages: 24

Brand: Magnavox Pages: 22

Brand: Magnavox Pages: 21

Magnavox FW 750C

Brand: Magnavox Pages: 28

Magnavox FW 2012

Brand: Magnavox Pages: 16

Brand: quadient Pages: 10

Pure Link 1300 Series

Brand: lancer Pages: 20

kb sound Series

Brand: EIS Pages: 2

Brand: Mark Climate Pages: 60

Brand: HAKO Pages: 6

Brauheld Pro 30

Brand: Klarstein Pages: 32

Brand: Fender Pages: 14

Brand: R. Beck Maschinenbau Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands