manualshive.com logo in svg

Kaise SK-8402, Instruction Manual

Share
Download
Kaise SK-8402 Instruction Manual Download Page 9

SK-8402 

取扱説明書（英文）

_P7

7

OPERATING PRECAUTIONS

Cautions for Handling

●

Do not apply mechanical shock.

 

The  shock  such  as  dropping  or  beating  might 
damage the instrument and may cause the trouble.

●

Do not pull cables forcibly.

 

Pulling  the  cables  forcibly,  such  as  when  removing 
the  plugs  from  terminal,  may  cause  the  cable 
disconnection.

●

It might cause the instrument trouble if taking the 
simulation  test  with  mischoice  the  type  of  O2 
sensor (zirconia, titania 1V or titania 5V).

●

Do not take the simulation test for heater cable or 
power  supply  cable  during  the  electric  car 
components are activated. It may damage to the 
instrument.

Cautions for safekeeping

●

Do not keep the instrument in the following place.

 ・

The place where has the water splash

 ・

The place where applies the hard shock

 ・

-20

℃

 or less, 60

℃

 or more, 70%RH or more

 ・

The place where has the condensation

 ・

The place where is exposed to direct sunlight

Summary of Contents for SK-8402













































Reviews:

No comments

Brands by name

Popular brands

Load more brands