manualshive.com logo in svg

Kaise SK-8402, Instruction Manual

Share
Download
Kaise SK-8402 Instruction Manual Download Page 21

SK-8402 

取扱説明書（英文）

_P19

19

PREPARATION FOR USE

⑥

Test lead wires have good continuity if "OL" blinks 
on LCD. Otherwise, they should be disconnected.
This concludes the test lead inspection.

●

Inspection for Check Harness

①

Connect  red  and  black  L-shaped  plugs  of  the  test 
lead to red (

＋

) and black (

−

) input terminals.

②

Connect  red  and  black  check  harness  connecting 
plugs to the red and black straight plugs respectively.

⑤

Short-circuit  red  and  black  male  connecting 
terminals and press TEST Key for 1 second or less 
to output RICH signal.

③

 Press POWER Key for 1 second or more to turn on 
the instrument. It enters stand-by mode for cable 
connection check.

④

Press  SEL  Key  for  1  second  or  more  to  enter 
simulation test mode for zirconia O2 sensor.

         lights up on LCD.

S

RICH

Z

S

APO

RICH

Z

S

APO

Red test lead straight plug

Red check harness

connecting plug

Black test lead straight plug

Black check harness

connecting plug

Press TEST Key for 1 second or less with contacting
the tips of red and black male connecting terminals.

O

2

 SENSOR CHECKER

SK-8402

TEST

SEL

Summary of Contents for SK-8402













































Reviews:

No comments

Brands by name

Popular brands

Load more brands