manualshive.com logo in svg

Kaise SK-8402, Instruction Manual

Share
Download
Kaise SK-8402 Instruction Manual Download Page 28

SK-8402 

取扱説明書（英文）

_P26

④

Start the engine.

⑤

If the zirconia O2 sensor to be measured has heater 
cables, make their voltage check. When measuring 
titania O2 sensor, make voltage check of its power 
supply cable.

※

The heater cable has the sufficient voltage even if 

"H"  display  is  unstable  when  checking  the  heater 

cable with PWM control.

※

Zirconia  O2  sensor  cannot  output  the  correct 
signal if heater is not working properly.

※

Titania  O2  sensor  cannot  output  the  signal  if 
the power supply voltage is not supplied.

26

NORMAL TEST

●

Do not touch the engine which has high temperature. 
Be careful about the cables not to touch the heated 
metal part.

●

Stay away from the rotating part of the engine which 
is  very  dangerous  to  be  caught  in. Also,  be  careful 
about the cables not to be caught in.

●

Start  the  engine  under  well  ventilated  environment 
to prevent carbon monoxide poisoning.

WARNING

Connect two yellow check harness connecting plugs  
to the red and black straight plugs respectively.

LCD  displays  "H"  if  the  heater  cable  has  the  proper 
voltage at 6V or more.

Checks of the heater cable voltage (when available)

V

Z

APO

Red test read straight plug

Yellow check harness

connecting plug

Black test lead straight plug

Yellow check harness

connecting plug

Only  for  the  heater  of  zirconia  O2  sensor, 
disconnection check for the heater cable is possible by 
simulation test. See "Disconnection check of the heater 
cable" in page 36 to 38 for details.

Summary of Contents for SK-8402













































Reviews:

No comments

Brands by name

Popular brands

Load more brands