manualshive.com logo in svg

Kaise SK-8402, Instruction Manual

Share
Download
Kaise SK-8402 Instruction Manual Download Page 18

BEFORE USE

SK-8402 

取扱説明書（英文）̲

P16

16

●

To prevent electric shock, detach the instrument from 
the measuring object and turn it off before installing 
or replacing the battery. 

●

To prevent electric shock, do not replace the battery 
with wet hands.

WARNING

●

Do  not  use  any  battery  that  have  wrong  rated 
specification.  It  may  cause  any  accidents  due  to 
explosion or leakage.

●

Install the battery with the correct polarity as shown in 
the plus

○

＋

 and minus

○

−

 indications. Installing battery 

with wrong polarity may cause any accidents due to 
explosion or leakage.

●

To  prevent  any  accidents,  dispose  the  exhausted 
battery in accordance with the local government rule 
after  applying  adhesive  tape  to  both  electrodes  for 
insulation. 

●

Do not heat or disassemble the battery. Do not put 
them  into  the  fire  or  water.  It  may  cause  any 
accidents due to explosion or leakage.

CAUTION

2. Battery Installation

①

Loosen  a  screw  of  battery  cover  and  open  it. 
Then,  insert  attached  2  pcs  of  batteries  with  the 
correct polarity as shown in the plus

○

＋

 and minus

○

−

 indications.

②

Fix battery cover and tighten up a screw.

NOTE : Pull the screw when the battery cover is  

hard to be opened.

Install attached batteries before using the instrument.

Insert attached two 1.5V
R6P batteries in correct
polarity.

1.5V R6P

1.5V R6P

Battery

Cover

Lift up the battery
cover with pulling
the loosened screw.

Screw

Screw

Summary of Contents for SK-8402













































Reviews:

No comments

Brands by name

Popular brands

Load more brands