manualshive.com logo in svg

KAESER M27, Operator'S Manual

Share
Download
KAESER M27 Operator'S Manual Download Page 115

10.2.3.1 Machine maintenance schedule

➤ Carry out maintenance tasks according to the following schedule.

Component:
Task

Daily

A250

A500

A1000

A1500

A2000

A3000

A36000

See chapter

Note

Engine:
Check inlet air filter mainte‐

nance indicator

X

10.3.2

Check engine oil level.

X

10.3.4

Engine

SM

Clean the engine air filter

X

10.3.2

Change the engine oil

X

10.3.4

Replace the engine oil filter.

X

10.3.5

Engine

SM

Check/adjust the drive belt ten‐

sion.

X

10.3.6

Engine

SM

Change the engine air filter.

X

10.3.2

Have the engine mounts

checked.

X

SW

Have the valve clearance adjus‐

ted.

X

SW

Engine

SM

Replace the drive belt.

X

10.3.6

SW

Engine

SM

Have the multi-ribbed belt / jock‐

ey wheel checked/replaced.

X

SW

Engine

SM

Check the engine coolant level.

X

10.3.1

Engine

SM

Clean the cooler.

X

10.5

Check coolant hoses and

clamps.

X

Check antifreeze concentration.

X

10.3.1

Engine

SM

Change the coolant.

X

10.3.1

Engine

SM

Fill up the fuel tank.

X

Clean the fuel filter.

X

10.3.3

Engine

SM

Clean the tank fuel strainer.

X

Engine SM = Engine manufacturer's service manual; SW = Specialized workshop

10 Maintenance

10.2 Maintenance schedules

No.: 9_9548 05  USE

Operator Manual    Screw Compressor   
M27  

105

Summary of Contents for M27







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands