KAESER M27 Operator'S Manual Download

Page: 65 / 294

6 Installation

6.1 Ensuring safety

Follow the instructions below for safe installation.
Warning instructions are located before a potentially dangerous task.

Disregard of warning instructions can cause serious injuries!

Complying with safety warnings

Disregard of safety warnings can cause unforeseeable dangers!
➤ Follow the instructions in chapter 3 “Safety and Responsibility”.
➤ Installation work may only be carried out by authorized personnel.

Further information Details of authorized personnel are found in chapter 3.4.2.

Details of dangers and their avoidance are found in chapter 3.5.

6.2 Reporting Transport Damage

1. Check the machine for visible and hidden transport damage.
2. Inform the carrier and the manufacturer in writing of any damage found.

6.3 Fitting the towbar

For space reasons, the machine is mounted on a transport frame when delivered.
■ Shifted adapter

of the height-adjustable towing device.

■ Disassembled adapter

of the height-adjustable towing device.

■ Shifted fixed-height towing device.
■ Disassembled fixed-height towing device.

Prior to removal of the transport frame, you must loosen the transport securing means and install

and/or adjust the towing device.

Material Protective gloves

Wrench
Hard rubber hammer

Precondition The machine is standing firm and level.

The machine is switched off.

Pinch hazard!

Severe pinching injury to fingers is possible.
➤ Always wear protective gloves.
➤ Work with caution.

Installation

6.1

Ensuring safety

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

Summary of Contents for M27







































































































































































































































































































Search results

Summary of Contents for M27

Reviews:

Related manuals for M27

Brands by name

Popular brands

KAESER M27, Operator'S Manual

Search results

Summary of Contents for M27

Reviews:

Related manuals for M27

Brands by name

Popular brands