Kaba Mas DKX-10 Installation Instructions Manual Download Page 36

Page: 36 / 38

Install Lock Cover

Locate the correct lock cover based on door handing. (

See Figure 30.)

(

Both a RHR (515031) and a LHR (515032) lock cover

are included in the Rim Exit Device box.)

B. Position

the lock cover over the lock cover mounting brackets. Locate the cover flush to the surface of the door and bias the

cover away from the door edge.

Secure the lock cover to the lock cover mounting brackets using four (4) #8-32 x

” PHMS

(105034)

screws. (

See Figure 30.

)

Install Manual O/R Knob Label

Upon completion of the CDX-10 Lock and Exit Device installation, locate (

515045)

nameplate label. Remove paper

backing, orient correctly, locate concentrically while applying pressure to adhere the label to the knob.

CDX-10

Cover, LHR

(515032)

CDX-10

Cover, RHR

(515031)

CDX-10

Nameplate

(515045)

CDX-10

Nameplate

(515045)

Figure 30

Summary of Contents for DKX-10







































Search results

Summary of Contents for DKX-10

Reviews:

Related manuals for DKX-10

Brands by name

Popular brands

Kaba Mas DKX-10, Installation Instructions Manual

Search results

Summary of Contents for DKX-10

Reviews:

Related manuals for DKX-10

Brands by name

Popular brands