Kaba Mas DKX-10 Installation Instructions Manual Download

Page: 3 / 38

Change BEST-Type Core

..............................................................................

Remove and Reassemble the Outside Lever .............................................. 21

Testing the Operation of the Lock .............................................................. 22

INSTALLATION (Phase Two)

..............................................................................

Dorma F9300 Fire Rated

.............................................................................

Install Strike

................................................................................................ 24

Install Panic Bar and Rail Assembly to Door

............................................... 25

Install End Cap

............................................................................................ 25

General Maintenance Notes

.......................................................................

INSTALLATION (Phase Three)

............................................................................

Install DKX-10/DKX-19 Lock Strike

................................................................

DKX-10/DKX-19 High Security Lock Installation ............................................ 27

Cut the Tubes................................................................................................ 28

DKX-10/DKX-19 High Security Lock Installation (Continued) ....................... 28

Install the Dial Ring ....................................................................................... 29

Install the Cables

..........................................................................................

Install Generator Cable and Cable Guides .................................................... 30

Install the Dial Ring Cover

.............................................................................

Cut and Install the Spindle

............................................................................ 30

Install the Dial Hub and Dial

......................................................................... 31

Interface Hardware ...................................................................................... 32

Cable Assembly

.................................................................................... 32

Install Knob Lever Assembly

................................................................

Install Lock Cable Assembly

................................................................. 33

Install Cable Assembly

......................................................................... 34

Connect Cable Assemblies

................................................................... 34

Adjust Cable Length

............................................................................. 34

Covers ........................................................................................................... 35

Install Chassis Cover

............................................................................ 35

nstall Lock Cover

.................................................................................

Install Manual O/R Knob Label

........................................................... 36

Summary of Contents for DKX-10







































Search results

Summary of Contents for DKX-10

Reviews:

Related manuals for DKX-10

Brands by name

Popular brands

Kaba Mas DKX-10, Installation Instructions Manual

Search results

Summary of Contents for DKX-10

Reviews:

Related manuals for DKX-10

Brands by name

Popular brands