background image

www.krain.com

RAIN SENSOR SELECT BUTTON

PROGRAMMING

05

The purpose of a rain sensor is to stop automatic
watering when sufficient precipitation has been
reached. 

The rain sensor select button allows the user 
to bypass the rain sensor. If a rain sensor has 
been installed, and BYPASSED has been selected, 
then BYPASSED will be displayed in the upper 
left corner of the LCD.

NOTE: When the rain sensor select button is 
in the ON position a rain sensor or wire jumper 
must be installed in order to run a program. 

Refer to page 13 for further details.

As the program dial is rotated the display 
automatically changes. The flashing value within the
display can be increased or decreased by pressing
the DOWN or UP buttons. To go back or advance to
the next value press the BACK or NEXT buttons.  

Because of variations in plant watering needs the
Pro-LC has three separate programming options; 
A, B and C. Each program is completely independent
of each other and the controller will automatically
stack programs that overlap. This allows for all
programmed watering to occur because only one 
program will run at a time and in alphabetical order. 

Only one start time per program (A, B or C) is
required to operate all stations with a run time. 
The controller automatically and numerically 
advances operation to the next station without
the need for additional start times.

For additional watering, each program can be set with
up to four separate start times. This allows for greater
irrigating efficiency when all watering can’t be done
during a single operation (cycle and soak).

NOTE: 

A program must contain at least one start

time, watering day(s) and one station with a run
time in order to operate.

WED 10:26

AM

A

PGM

BYPASSED

Summary of Contents for PRO-LC





























Reviews: