background image

2

SPECIFICATIONS

* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Blade No.31 ................................................................. 1

For cutting thick lumber

(2) Splinter guard ............................................................. 1
(3) Chip cover ................................................................... 1
(4) Hexagonal bar wrench ............................................... 1
Standard accessories are subject to change without
notice.

OPTIONAL ACCESSORIES (sold separately)

(1) Blades, No.1 – No.6, 31*

* No.31 Blade is a standard accessory.

(2) Guide
Optional accessories are subject to change without notice.

APPLICATIONS

Cutting various lumber and pocket cutting

Cutting mild steel plate, aluminum plate, and copper
plate

Cutting synthetic resins, such as phenol resin and
vinyl chloride

Cutting thin and soft construction materials

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.

3. Extension cord

When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.

MOUNTING THE BLADE

1. Use the accessory hexagonal bar wrench to loosen

the blade set screws on the blade holder, as shown in
Fig. 1(a).

2. Holding the blade with its cutting edge facing the

front, insert the mounting portion of the blade into
the plunger groove until it touches the bottom of the
groove.

3. As shown in Fig. 1(b), firmly clamp the side screw.

CAUTION

Loosened set screws may cause the blade to be
damaged. Always ensure that the set screws are
securely tightened. Always ensure that the plunger
groove is clean and clear of sawdust to ensure proper
blade mounting and set screw clamping.

4. Storing the hexagonal bar wrench
(1) Insert in a hole on the side of the main unit with

holding the short side horizontally as shown in
Fig. 2.

Voltage (by areas)*

(110V, 115V, 120V, 127V, 220V, 230V, 240V)

Power input

400W*

Wood: 65mm

Max. cutting depth

 Mild steel: 6mm

No-load speed

0 – 3000 min

–1

Stroke

18mm

Min. cutting radius

25mm

Weight (without cord)

1.5kg

Fig. 1(a)

Fig. 1(b)

Blade set screw

Hexagonal bar wrench

Blade set screw

Roller

Blade (blade edge
must face front)

Blade holder

Summary of Contents for EJS120PV













Reviews: