JVC GR-DVP8, Instructions Manual

Page: 57 / 84

EN
57
Master Page: Right
1
Load the provided memory card. (
墌
pg. 16)
Then, perform step 1 and 2 of “Audio Dubbing”
(
墌
pg. 56).
2
Press MENU . The Menu Screen appears.
3
Press + or – to select “ s ”, and press SET/
SELECT . The SYSTEM Menu appears.
4
Press + or – to select “SOUND IN”, and press
SET/SELECT . The Sub Menu appears.
5
Press + or – to select “D.SOUND”, and press
SET/SELECT .
6
Press + or – to select “
B
RETURN”, and press SET/
SELECT twice. The Menu Screen closes and the
sound effect indication appears.
7
Press INDEX to access the sound effects Index
Screen.
8
Press + or – to select the desired sound effect and
press SET/SELECT .
9
Press PLAY (
U
) to begin Audio Dubbing. The
selected sound effect is dubbed onto the tape.
●
The “ ” moves while it is being dubbed.
●
To stop dubbing the sound effect midway, press
D.SOUND .
10
Press STOP (
8
) to end Audio Dubbing.
NOTES:
●
After dubbing, set “SOUND IN” back to “MIC/
AUX”.
●
The dubbed sound effect is recorded on
SOUND 2. (
墌
pg. 40)
●
If you press PAUSE (
9
) to pause dubbing in step 9
the selected sound effect indication remains
displayed. To resume dubbing, press
PLAY (
U
).
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
NOTES:
●
Before performing the following steps, make sure
that “TIME CODE” is set to “ON”. (
墌
pg. 31, 41)
●
Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
●
To perform Insert Editing while watching in the
television, make connections. (
墌
pg. 22)
1
Play back the tape, locate the Edit-Out point and
press
PAUSE (
9
). Confirm the time code at this
point. (
墌
pg. 41)
2
Press REW (
3
) until the Edit-In point is located,
then press PAUSE (
9
).
3
Press and hold INSERT (
I
) on the remote
control, then press PAUSE (
9
). The “
9
I ”
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
4
Press START/STOP to begin editing.
●
Confirm the insert at the time code you
checked in step
1 .
●
To pause editing, press START/STOP . Press it
again to resume editing.
5
To end Insert Editing, press START/STOP , then
STOP (
8
).
NOTES:
●
Program AE with special effects (
墌
pg. 33) can be
used to spice up the scenes being edited during
Insert Editing.
●
During Insert Editing, the date and time
information changes.
●
If you perform Insert Editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
●
During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Edting stops. (
墌
pg. 80, 81)
●
If a memory card is loaded and “NAVIGATION” is
set to other than “MANUAL”, a NAVIGATION
thumbnail image is stored in the memory card.
(
墌
pg. 47)
Insert Editing
PAUSE
START/STOP
INSERT
PLAY
REW
STOP
AD
V
A
NCED FE
A
TURE
S
GR-DVP9US.book Page 57 Wednesday, January 22, 2003 5:35 PM