0106
.GB
F 9
6.4
Checking the mounting and the attachment of the drive wheel
– Prepare the truck for the performance
of servicing and maintenance opera-
tions (refer to section 6.1).
– Open the front hood (refer to section
6.2).
– Separate the control lead connections
to the standing platform (6).
– Unscrew the standing platform attach-
ment screws (7) and remove the
standing platform (this step also ap-
plies to the fixed driver standing plat-
form).
– Raise the truck so that the driven
wheel (8) can rotate freely.
– Turn the driven wheel by hand and
check that it runs noiselessly.
– Lower the truck to the ground again.
– Swivel the control shaft fully to the left.
– Using a torque wrench, tighten the
wheel screws (9) crosswise.
Z
Tightening torque
– Step 1 - M
A
= 10 Nm
– Step 2 - M
A
= 105 Nm
– Mount the standing platform (4) and secure it in place by means of the attachment
screws.
– Reconnect the control lead connections to the standing platform.
6.5
Checking the hydraulic oil level
– Prepare the truck for the performance
of servicing and maintenance opera-
tions (refer to section 6.1).
– Open the front hood (refer to
section 6.3).
– Check the hydraulic oil level at the hy-
draulic oil reservoir (11).
Z
The hydraulic oil reservoir is provided
with markings (10). With the fork in the
lowered position, the oil level must be
between the markings “max.” and
“min.”.
If necessary, top up to the “max.” mark-
ing using hydraulic oil of the prescribed
specification (refer to the hydraulic oil
specification, section 5).
JUNGHEINRICH
JUNGHEINRICH
JUNGHEINRICH
7
7
6
8 / 9
min
max
11
10
0106
.GB
F 9
6.4
Checking the mounting and the attachment of the drive wheel
– Prepare the truck for the performance
of servicing and maintenance opera-
tions (refer to section 6.1).
– Open the front hood (refer to section
6.2).
– Separate the control lead connections
to the standing platform (6).
– Unscrew the standing platform attach-
ment screws (7) and remove the
standing platform (this step also ap-
plies to the fixed driver standing plat-
form).
– Raise the truck so that the driven
wheel (8) can rotate freely.
– Turn the driven wheel by hand and
check that it runs noiselessly.
– Lower the truck to the ground again.
– Swivel the control shaft fully to the left.
– Using a torque wrench, tighten the
wheel screws (9) crosswise.
Z
Tightening torque
– Step 1 - M
A
= 10 Nm
– Step 2 - M
A
= 105 Nm
– Mount the standing platform (4) and secure it in place by means of the attachment
screws.
– Reconnect the control lead connections to the standing platform.
6.5
Checking the hydraulic oil level
– Prepare the truck for the performance
of servicing and maintenance opera-
tions (refer to section 6.1).
– Open the front hood (refer to
section 6.3).
– Check the hydraulic oil level at the hy-
draulic oil reservoir (11).
Z
The hydraulic oil reservoir is provided
with markings (10). With the fork in the
lowered position, the oil level must be
between the markings “max.” and
“min.”.
If necessary, top up to the “max.” mark-
ing using hydraulic oil of the prescribed
specification (refer to the hydraulic oil
specification, section 5).
JUNGHEINRICH
JUNGHEINRICH
JUNGHEINRICH
7
7
6
8 / 9
min
max
11
10
Summary of Contents for ERE 224
