Jungheinrich DFG 425, Operating Instructions Manual

Page: 78 / 103

F 1
02
.0
8.
GB
F Maintenance of the Forklift Truck
1 Operational Safety and Environmental Protection
The servicing and inspection duties contained in this chapter must be performed in
accordance with the intervals indicated in the servicing checklists.
F
Any modifications to the forklift truck assemblies, in particular the safety mechanisms,
is prohibited. The operational speeds of the truck must not be changed under any
circumstances.
M
Only original spare parts have been certified by our quality assurance department. To
ensure safe and reliable operation of the forklift truck, use only the manufacturer's
spare parts. Used parts, oils and fuels must be disposed of in accordance with the
relevant environmental protection regulations. For oil changes, contact the
manufacturer’s specialist department.
Upon completion of inspection and servicing, the tasks contained in the
“Recommissioning” section must be performed (see chapter
F).
2 Maintenance Safety Regulations
Maintenance personnel: Industrial trucks must only be serviced and maintained by
the manufacturer’s trained personnel. The manufacturer’s service department has
field technicians specially trained for these tasks. We therefore recommend a
maintenance contract with the manufacturer’s local service centre.
Lifting and jacking up: When an industrial truck is to be lifted, the lifting gear must
only be secured to the points specially provided for this purpose. When the truck is to
be jacked up, take appropriate measures to prevent the truck from slipping or tipping
over (e.g. wedges, wooden blocks). You may only work underneath a raised lifting
device if it is supported by a sufficiently strong chain.
Z
Jacking point see chapter B.
Cleaning: Do not use flammable liquids to clean the industrial truck. Prior to cleaning,
all safety measures required to prevent sparking (e.g. through short circuits) must be
taken. For battery-operated trucks, the battery connector must be removed. Only
weak suction or compressed air and non-conductive antistatic brushes may be used
for cleaning electric or electronic assemblies.
M
If the truck is to be cleaned with a water jet or a high-pressure cleaner, all electrical
and electronic components must be carefully covered beforehand as moisture can
cause malfunctions.
Do not clean with pressurised water.
After cleaning the truck, carry out the activities detailed in the “Recommissioning”
section.
F 1
02
.0
8.
GB
F Maintenance of the Forklift Truck
1 Operational Safety and Environmental Protection
The servicing and inspection duties contained in this chapter must be performed in
accordance with the intervals indicated in the servicing checklists.
F
Any modifications to the forklift truck assemblies, in particular the safety mechanisms,
is prohibited. The operational speeds of the truck must not be changed under any
circumstances.
M
Only original spare parts have been certified by our quality assurance department. To
ensure safe and reliable operation of the forklift truck, use only the manufacturer's
spare parts. Used parts, oils and fuels must be disposed of in accordance with the
relevant environmental protection regulations. For oil changes, contact the
manufacturer’s specialist department.
Upon completion of inspection and servicing, the tasks contained in the
“Recommissioning” section must be performed (see chapter
F).
2 Maintenance Safety Regulations
Maintenance personnel: Industrial trucks must only be serviced and maintained by
the manufacturer’s trained personnel. The manufacturer’s service department has
field technicians specially trained for these tasks. We therefore recommend a
maintenance contract with the manufacturer’s local service centre.
Lifting and jacking up: When an industrial truck is to be lifted, the lifting gear must
only be secured to the points specially provided for this purpose. When the truck is to
be jacked up, take appropriate measures to prevent the truck from slipping or tipping
over (e.g. wedges, wooden blocks). You may only work underneath a raised lifting
device if it is supported by a sufficiently strong chain.
Z
Jacking point see chapter B.
Cleaning: Do not use flammable liquids to clean the industrial truck. Prior to cleaning,
all safety measures required to prevent sparking (e.g. through short circuits) must be
taken. For battery-operated trucks, the battery connector must be removed. Only
weak suction or compressed air and non-conductive antistatic brushes may be used
for cleaning electric or electronic assemblies.
M
If the truck is to be cleaned with a water jet or a high-pressure cleaner, all electrical
and electronic components must be carefully covered beforehand as moisture can
cause malfunctions.
Do not clean with pressurised water.
After cleaning the truck, carry out the activities detailed in the “Recommissioning”
section.