Jung FM ST 50 UP Operating Instructions Manual Download Page 8 | Manualshive

Page: 8 / 11

Jung FM ST 50 UP Operating Instructions Manual Download Page 8

Dimming adjustment time

1…60 s
Basic setting: 4 s

Time from minimum
brightness until reaching
maximum brightness (dimming
speed).

Run-on time

0 s … 24 h
Basic setting: 0 s

As soon as a run-on time has
been entered, the actuator will
no longer remain on
permanently, but only for the
length of the run-on time. The
run-on time is restarted if
actuation is repeated. This
parameter is directly
connected to the "Manual
switch-off of run-on time"
parameter.
Note: The set time apply to
operation using radio
transmitters. The device is
switched immediately when
the

Prog

button is pressed.

Behaviour after the end of the
disabling function

On
Off
no change
Last value
Basic setting: No change

Behaviour of the output when
a block is removed.

Behaviour on voltage return

On
Off
Last value
Configured brightness
Basic setting: Off

Defines the behaviour of the
output after voltage return.

Brightness on voltage return

0...100 %
Basic setting: 100 %

Brightness value, set by the
output after voltage return
(mains voltage). The
parameter "Behaviour after
voltage return" must be set to
"Configured brightness".
Note: If the value is above the
set maximum brightness or
below the minimum
brightness, then the system
will switch to the appropriate
limit value.

8/11

82581013
J:0082581013

13.03.2014

eNet

Radio push-button controller 1-10 V

«
...
6
7
8
9
10
...
»

Summary of Contents for FM ST 50 UP












Reviews:

No comments