manualshive.com logo in svg

Jung FM ST 50 UP, Operating Instructions Manual, Page: 2 / 11

Share
Download
Jung FM ST 50 UP Operating Instructions Manual Download Page 2

Intended use

-

Switching and brightness setting of luminaires with 1-10 V interface

-

Operation with suitable radio transmitters

-

Mounting in appliance box according to DIN 49073 in combination with a suitable cover.

-

Installation in surface-mounted housing or panel-mounted housing (accessories) for
suspended ceilings

Product characteristics

-

Switch-on brightness can be saved permanently

-

Minimum brightness can be saved permanently

-

Scene operation possible

-

Status indicator of the 1-10 V subscribers via LED

-

Status feedback to radio transmitter

-

1-10 V subscribers switchable with 

Prog

 button

-

1-10 V interface is protected against reverse polarity 

Can be set with eNet server:
-

Maximum brightness

-

Dimming speed

-

Switch-on delay / switch-off delay

-

Dim up/dim down ramp

-

Switch-off warning

-

Operation locks

-

Continuous on, Continuous off

-

Hotel function

-

Run-on time

-

Light control

i

If settings are changed with the eNet server, operation and signalling could vary from what
is described here.

i

The parameter list is in the Internet in the documentation for this device.

Supplementary functions with eNet server: 
-

Update of the device software

-

Repeater function

-

Reading of error memory

Response after mains voltage return

The response after mains voltage return can be configured with the eNet server. Default setting:
Off.

4 Operation

Operation with radio transmitters

Operation is with radio transmitters, please observe the radio transmitter instructions.

5 Information for electrically skilled persons

5.1 Fitting and electrical connection

DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.

Mounting and connecting actuator

To ensure good transmission quality, keep a sufficient distance from any possible sources of
interference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts or
transformers. 

2/11

82581013
J:0082581013

13.03.2014

eNet

Radio push-button controller 1-10 V

Summary of Contents for FM ST 50 UP












Reviews:

No comments