background image

IMPORTANT

Read the following statements and warnings to avoid serious or fatal injury.

Warning. 

-  Max 150 kg. 

-  Only for domestic use. 

-  Outdoor use.

-  Only one user. Collision hazard.

-  The net should be replaced every year.

-  Adult supervision required.

-  Do not perform somersaults (flips).This is very dangerous and you risk serious injury or death

-  Always close the safety net opening before jumping.

-  Read the instructions.

-  The trampoline shall be assembled by an adult in accordance with the assembly instructions

  and then checked before the first use

-  Jump with proper gym shoes or barefoot only.

-  Empty pockets and hands before jumping.

-  Always jump in the middle of the mat.

-  Do not use when the mat is wet.

-  Do not eat while jumping.

-  Do not exit by a jump.

-  Limit the time of continuous usage (take regular breaks).

-  Do not use in strong wind conditions and secure the trampoline.

-  Do not try to jump over the net.

-  Do not purposely jump onto the net. 

-  Do not try to purposely rebound off the safety net. 

-  Do not hang on the top of the net, or try to climb the netting. 

-  Take off any jewellery that could become entangled with the netting or cut the netting.  

Placement of the trampoline

Do not place the trampoline on a concrete floor or other hard surfaces. The ideal placement is a 

level, stable surface like a lawn. There must be at least 2 meters of space around the trampoline. 

Check that there are no wires, tree branches, fences or other possible hazards above and around 

the trampoline. The trampoline should not be placed near any pools, swings, slides, climbing 

frames or other obstructive installations. The trampoline is not intended to be buried into the 

ground. 

Weather conditions

The trampoline should not be used when wet. In winter conditions, please disassemble the 

trampoline and store all fabric parts (mat, foam pad, safety net) inside. In strong wind conditions, 

disassemble the foam pad and safety net and secure the trampoline to the ground using Ground 

Stakes/Anchors (sold separately).

How to use 

Take it easy at first. Don’t try difficult move

Do not jump when tired - this increases the risk of injury. Be sure to wear proper shoes, e.g. gym 

shoes, or be barefoot when jumping.

Never step on the frame pad. It is not constructed to support the weight of a person. Never 

dismount by jumping off the trampoline. Always climb off. Don’t use the trampoline under the 

influence of drugs or alcohol.

Always have someone else watching while you jump. If you should injure yourself you will have 

someone to assist you.

Always start your jump at the centre of the mat. If you land more than 30 cm away from the edge 

of the logo, stop your jump immediately!

Restart your jump at the centre of the mat. 

Assembly

Please read the assembly instructions fully before starting to assemble the trampoline. It is 

advisable to have two people assembling it together.

Start first by checking that you have all the required parts. The reference No. of each part will be 

used in the instructions to guide you.

2

Summary of Contents for Extreme 426cm





























Reviews: