JUKI LS-2342 Instruction Manual Download Page 5

Page: 5 / 31

– 3 –

1) To prevent possible accidents caused by the full of

the sewing machine, perform the work by two per-
sons or more when the machine is moved.

Loosen bed cover mounting screws

❶

(three lo-

cations) to remove them. Remove bed cover

❷

Then, carry the sewing machine by holding pulley
cover

❸

Do not hold the handwheel and the reverse
feed lever.

2) Do not put protruding articles such as the screw-

driver and the like at the location where the sewing
machine is placed.

❶

❷

❹

❸

1) Attach oil extractor

❶

onto the top surface of the

machine table, and fix it with setscrew

❷

and wash-

❸

2) After fixing oil extractor

❶

, screw drain container

❹

in the oil extractor.

2-1. Attaching the drain container

2-2. Installation of the sewing machine

2. INSTALLATION

❶

❸

❷

Summary of Contents for LS-2342
































Search results

Summary of Contents for LS-2342

Reviews:

Related manuals for LS-2342

Brands by name

Popular brands

JUKI LS-2342, Instruction Manual

Search results

Summary of Contents for LS-2342

Reviews:

Related manuals for LS-2342

Brands by name

Popular brands