JUKI LS-2342 Instruction Manual Download Page 22

Page: 22 / 31

– 20 –

The safety clutch functions when an excessive load is applied

to the hook or the other components during sewing. At this time,

the hook will never rotate even if turning the handwheel. When

the safety clutch has functioned, remove the cause and reset the

safety clutch as given in the following procedure.

1) Pressing push button

❶

located on the top surface of the ma-

chine bed, strongly turn the handwheel in the reverse direction

of rotation.

2) The resetting procedure completes when the handwheel clicks.

Turn the handwheel by hand, and confirm that push

button

❶

has returned.

3) At the final step of procedure, check the needle-to-hook rela

tion. (Refer to

"4-5. Needle-to-hook relation" p.17

To lift the presser foot manually, pull hand lifter

❶

in the direction

of the arrow.
This makes the presser foot rise 10 mm and stay at that position.

5-1. Hand lifter

5-2. Resetting the safety clutch

5. OPERATION OF THE SEWING MACHINE

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the follow-

ing work after turning the power off and ascertaining that the motor is at rest.

To prohibit the adjustment of the feed adjusting dial:

1) Remove the pulley cover.
2) Insert stopper pin

❷

and screw

❸

in tapped hole

❶

and tight-

en it.

Insert stopper pin

❷

into the tapped hole from its thinner end

as illustrated in the figure.

Stopper pin

❷

and screw

❸

are separately available.

Part number of stopper pin : TA0440401MO
Part number of screw

: SM8060612TP

5-3. Fixing the feed adjusting dial

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the follow-

ing work after turning the power off and ascertaining that the motor is at rest.

❶

❸

❷

❶

Summary of Contents for LS-2342
































Search results

Summary of Contents for LS-2342

Reviews:

Related manuals for LS-2342

Brands by name

Popular brands

JUKI LS-2342, Instruction Manual

Search results

Summary of Contents for LS-2342

Reviews:

Related manuals for LS-2342

Brands by name

Popular brands