JUKI LS-2342 Instruction Manual Download Page 23

Page: 23 / 31

– 21 –

5-4. Normal-/reverse-feed stitch needle entry points alignment at the

time of automatic reverse feed stitching (LS-2342S-7, 2342H-7)

When the sewing speed or stitch pitch is changed, the normal- and reverse-feed stitch needle entry points may

not be aligned at the time of automatic reverse feed stitching.

In such a case, correct the alignment of needle entry points by changing the ON/OFF timing of the automatic re-

verse feed cylinder.

In the case the stitch pitch is large and correction of the timing is difficult, it is recommended to decrease the re

verse feed sewing speed or use the temporary stop function at each corner section of the sewing pattern.

Refer to

"III-8. Detailed explanation of selection of functions

⑯

Compensation of timing of the solenoid for

reverse feed stitching"

in the Instruction Manual for the SC-922 for detail.

Normal- and reverse-feed stitches may need to be adjusted according to the stitch pitch to be used. Refer to the

Engineer's Manual for how to adjust the stitches.

1) How to align needle entry points of the reverse feed stitching with those of the normal feed stitching

Carry out "correction of the timing of the reverse feed stitching" according to the difference between the needle

entry points of the reverse feed stitching and those of the normal feed stitching.

Refer to

"III-6. Setting the SC-922 functions"

in the Instruction Manual for the SC-922 for how to carry out

the "correction of the timing of the reverse feed stitching".

2) Stitch-by-stitch reverse feed stitching speed (Function setting No. 8)

Default value

Recommended value Recommended value

Stitch pitch (mm)

3 to 6

7 to 8

Reverse feed stitching speed (sti/min)

600

500

400

②

Correction of the OFF-timing of the re-

verse feed stitching at the beginning of
sewing (Function setting No. 52)

③

Correction of the OFF-timing of the re-

verse feed stitching at the end of sewing
(Function setting No. 53)

Sewing starting position

Stitch length

is smaller.

Decrease the set

value of No. 51.

Increase the set

value of No. 51.

Decrease the set

value of No. 52.

Increase the set

value of No. 52.

Stitch length is smaller.

Decrease the set

value of No. 53.

Increase the set

value of No. 53.

Stitch length is smaller.

Sewing end position

①

ON-timing of the reverse feed stitching at

the beginning of sewing (Function setting
No. 51)

Summary of Contents for LS-2342
































Search results

Summary of Contents for LS-2342

Reviews:

Related manuals for LS-2342

Brands by name

Popular brands

JUKI LS-2342, Instruction Manual

Search results

Summary of Contents for LS-2342

Reviews:

Related manuals for LS-2342

Brands by name

Popular brands